Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hello!
I am new to controller programming. My work at the institute is connected with bluetooth research, so I need to learn how to program nrf52840. My microcontroller...
So I looked at the example of the temprature read and I got the following code:
But the problem I got is with the: while (NRF_TEMP->EVENTS_DATARDY == 0), I don't want...
I read the discussion in the following link, but my application is different so I want to ask for advice on how to proceed.
https://devzone.nordicsemi.com/f/nordic-q-a/50642...
Hi all,
I successfully flashed the peripheral_hr sample from the Getting Started guide into my nRF5340 PDK (from here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hi,
I am new to the SAADC concept in nrf52. I have to measure the battery voltage using SAADC over ANI0 pin. I using battery with voltage 4.1 volt.
This voltage is divided...
Hi nordic,
In our project we are using pairing and bonding process. the first pairing with the iphone was successful, I delete the NRF52832 pairing infomation,iphone pairing...
Hello ...
Our product (nRF52810, SDK 15.3.0, SD 112 6.1.1) allows the user to change the device name, which typically happens once when new product is received. Our app...
I am running the ADC demo for the 52833-DK (pca10100) and can’t seem to get any valid readings. SDK 16.0: examples\peripheral\saadc
I am applying 1.5V to AIN0 on P8 and...
Hi, I am developing something using Zephyr on a nRF52840-DK as one Bluetooth mesh node and a Thingy as the other. To program the Thingy, I have it connected the Thingy to...
Hello -
I am trying to run the USB CDC ACM example on macOS 10.12.6. Following the instructions in the example app, I should see a virtual COM port as /dev/ttyACMx when...
Hello,
I am doing some testing on the nrf52832 DK using the mesh light switch example, i am sending ACK messages, i would like to log the time it takes the message to reach...
Hi,
What is the proper way to set "real time" in nRF9160 with nRF Connect SDK?
I want the function time() from the file time.h to return the correct time.
I know that...
I am using SDK15.3.0 and softdevice 6.1.1 on a nrf52DK.
I have a binary (compiled contiki application) that works when I flash it using nRF Connect. It is flashed from address...
Hi,
I have a PCA10040 board (nRF52-DK) which has a P20 debug out interface. I've got another nRF52832 breakout board which has VCC/SWIO/SWCLK/GND wires for debug/programming...
Hey,
I configured one device as low power node in mesh network.
With the button press interrupt low power node wakes up and perform some operation (publish BLE message...
