I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hello,
nRF51822
SDKv11
Kail 5.18
SD130
I have a pcb that has a sensor with I2C. I made a project that based on the sample of "twi_sensor", and I can read the sensor...
Hi all, I am trying to build the beaconing example from the nRF5 SDK for Mesh. When running:
$ ninja flash_beaconing_nrf52832_xxAA_s132_6.0.0
I get the following error...
I have 3 nRF52840 dongles and want to setup a mesh network between them. Which example from the SDK should I execute and how will i come to know if its working fine.
Hello all!
I'm using a nRF52 DK, which has been already programmed with the soft device s212, since my interest is to be able to connect to sensors using ANT+.
My purpose...
Hi,
We are currently testing DRX (not eDRX) on our custom board, and we would like to reduce the power consumption.
When everything on the board is in low power mode,...
Hi Goature,
We are also try to implement the same. We aren't getting any idea how to start. Refer the same thread : devzone.nordicsemi.com/.../make-ble-central-send-firmware...
Hi there,
Is there any Zigbee Motion Sensor code example that someone has put together? I could not find any on the nRF5 SDK for Thread and Zigbee.
Thanks
Hello,
Was programming two different boards today with the new 1.1.0 modem firmware.
Programmer reported the following for the two boards.
2019-11-21T21:10:34.297Z...
Hello!
Some time ago you seem to bundle sample 5 x nRF52832 to nRF52DK. Recently there was no bundled chips. Why did you change that?
The development and prototyping...
Hello, I tried to set up my nRF9160 with this tutorial and there is a problem: https://www.youtube.com/watch?v=jZQcmU3KIMY&t=216s
According to the tutorial, LED 3 and the...
I'm investigating the PDM peripheral on the nRF52840 and I have not been able to find out what the RATIO configuration bit actually does.
Presumably it controls how aggressive...
Hello,
I try to solve one problem with SYSTEM OFF and I still have no idea.
In my device I have one button switch and with this button I need to change characteristic...
I am using nrf52832 modules connected in mesh light switch example configuration from mesh V 3.2.0 i am unable to send a array over mesh i have gone through various posts...
I wanna know that, is latest SDK has demo example which will convert nRF52 SoC
to act like basic 2.4 Ghz transceiver (who should by default remain in Receiver mode &
switch...
Hi guys,
My question is really general: How do I reduce the TX Power of an nrf51822 BLE beacon?
The situation is the following:
1. I ordered this device: https://www...
