Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
I'm having problems getting the DFU dual bank ble s110 example to work on my target. My custom BLE app on my target is running fine, so my hardware is all good, and the DFU...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
I'm using s132_nrf52_2.0.0-7.alpha_softdevice. I've verified that the soft device is enabled.
void rdi_set_gap_parameters(void)
{
uint32_t err_code;
ble_gap_conn_params_t...
Is there are working example of FreeRTOS running on the nRF52 using the S132 SoftDevice? I am trying to get a ble_hrs example running with a updated version of the FreeRTOS...
Hi,
We have a rev3 nrf51822 system running S110 v7.3 and using SDK6.1.0. We are having trouble tracking down a ~1mA baseline current consumption when in system on/low power...
I'm struggling to understand this strange issue. I have a firmware based on S110 SD on nRf51822-QFABA0, this firmware is still based on version 7.1.0. The application is based...
I'm working on a program which sends 20 kb of data (sending 16 byte at a time) with one condition which is that indication should be enabled first. the first function checks...
Hi. i use SDK 9.0.0 and S130_1.0.0.
I want to recieve data from My peripheral S110..
First, I try to recieve data using example "ble_app_uart_c_S120-master".
I could...
Conditions in www.nordicsemi.com/.../Why-can-Master-Control-Panel-not-find-my-Master-Emulator-Dongle have been met, ie all components of PCA10031 have installed successfully...
in the answer of this question it said that :
You are also not allowed to send a new
indication until the previous one is
confirmed. This is signaled by the
reception...
I found this: github.com/.../nordic-nrf52832-gcc and tried to add it (and its dependency to the nordic-nrf52832-gcc 0.1.0 target to yotta with no luck. Is there a description...
Is there a maximum consecutive receive time similar to the maximum consecutive transmit time? I am operating in 1 Mb/s ESB mode. I am seeing the Rx get disabled approximately...
I am developing a ble program for the nrf51 DK using mbeds api and it is supposed to send 11 packets (notifications) when written to a specific handle. So far it works, but...
I'm receiveing this error 7 on line error 296. the only APP_ERROR_CHECK on line 296 is hci_slip_rx_buffer_register . this documentation doesn't not give any description of...
