Both computers have ncs2.9.0_nrf54h20_1 SDK installed
The same project is compiled on these two computers, the firmware zephyr.hex is different, but the zephyr.bin is the...
Hello DevZone,
Is it possible to support Matter over Ethernet and Matter over Wi-Fi at same time?
Since there are many Ethernet chips support in Zephyr.
Seems that the...
We are using nRF5340 with nRF7002 on our custom board. Our application requires:
Wi-Fi (via nRF7002)
Thread (via nRF5340)
DFU over Wi-Fi
We are concerned...
Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Hi,
I'm looking to continuously sample the ADC at a high sample rate with rotating buffers.
I found an example code that matches what I need with the older SDK for...
Hi.
I have been investigating how to use GRTC and LFXO for LFCLK with nRF54L15DK. In my goal, I would like to make the Intermittent application with sleep and GRTC that...
I am implementing sha256 with hash message bigger than or equal to 8KB. I tried with nrf54l15dk_nrf54l15_cpuapp target, and it's working fine but if I try with nrf54l15dk_nrf54l15_cpuapp_ns...
I will try to use the s110 8.0.0
But I can not find the sdk installer from the website.
Three months ago, when I visited the website, there is a SDK 6.xx.xx Installer...
Hi.
I'm currently receiving advertisement packet from beacon scanner app. (nrf51822)
(ble_peripheral/experimental_ble_app_multiactivity_beacon/hrs_scanner)
I tried...
Hi, I am here in the use of Flash memory data when there is a strange question to consult.
Due to my side of the application, you need to enter each case sd_power_system_off...
Using nRF51 SDK 10.0, it seems like many debug prints are incorrect, triggering a GCC format warning resulting in a compilation error with -Wall turned on.
A workaround is...
I'm using a custom designed PCB around the NRF51822 that broadcasts accelerometer readouts on a characteristic.
The application is based on s110 uart example and has been...
i wantto compile ''ble_app_hrs_c'' from sdk
but it always show up likes
" C:\Program Files\CodeBlocks\MinGW\include\SDK 7.2\examples\ble_central\ble_app_hrs_c\main.c|19...
keil use pclint, it will give lots of info message or warning message.what 's the best configuration to filter these info message ?? just display the error or warning message...
Hi
I'm trying to test UART over BLE using A custom board with a nRF51822,S110_NRF51822_7.1.0
SDK 6_1_1, Code is Github "NordicSemiconductor/nRF51-ble-app-uart-static-passkey...
I'm a beginner, the question might be simple but its really important for me.
What would the current flowing through Empty nrf51822 when it is completely erased or empty...
In bootloader of sdk9
I find
ble_gap_addr_t addr;
err_code = sd_ble_gap_address_get(&addr);
APP_ERROR_CHECK(err_code);
// Increase the BLE address by one when advertising...
Dear sir,
We are using the NRF24LU1P-F32Q32-T chipset.We have unmounted chip that we are using for our application .We have made a pcb developement board on NRF24LU1P-F32Q32...
Hi,
In my project I am using rev3 nrf51822-QFAA chip set with s130 soft device.while I compiling getting the error "region RAM overflowed with stack". Then I followed some...
