Hi,
I have set up a destination in the the NRF Cloud Message Routing Service
The destination has been verified and I can successfully send the test message from NRF Cloud...
Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
In the examples\bsp\bsp.h file there is a typo on line 61:
#define BSP_APP_APP_TIMERS_NUMBER 0
It should be:
#define BSP_LED_APP_TIMERS_NUMBER 0
Where is the...
I'm building out a project in Keil using the latest SDK (9.0) and the S130 Soft Device, and during build, Keil complains in mem_manager.c that sdk_config.h isn't there:
...
Hello, I'm currently using the nrf51822 and I'm constantly trying to send the accelerometer data to the NRF UART v2.0 Android Application.
But I do not know what I would...
Hi:
I want to get frequence hopping with gzl, Now I finish config gzl and commuicate successful between host and device. But I don't know whether frequence hop successful...
In s110 sdk 8, peripheral can connect one master and advertise in a non-connectable state simultaneously by here
but I did not find out how to confing non-connectable advertise...
This call:
SEGGER_RTT_printf(0, "%sHello %s%s%s!\n", RTT_CTRL_RESET, RTT_CTRL_BG_BRIGHT_RED, RTT_CTRL_TEXT_BRIGHT_WHITE, "World");
Produces this output on the J-Link...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
Hello everyone:
i'm testing the iot SDK 8.0, but got some problem with that.
Using the CoAP observable server example with it.
env: pca10028 + ble dongle + raspberry...
Hi,
What is the maximum rating for the nRF51's input RF level? It is not specified in the Product Specification for 51, though it is for 52.
Thanks,
Steve
By the migration of my application from nRF51 to nRF52, I can't compile the Nordic driver: nrf_delay.c
The IAR-Compiler gives that output by the build:
Error[Og010]...
Hi ,
I am using 2450bm14e0003 this instead of LNA circuit provided by NRF24L01P-R7 .Is it better to use this balun Ic or i should use the circuit provided by nordiac only...
I want to make a Bluetooth connection with nrf51422.
I am using the Keil software.
But I do not understand what the program will do the bluetooth connection.
Can you help...
I am running the Blinky code provided in nRF52 SDK examples.I am not able fix this error pointing at nrf_delay_ms. This function is hard to explain. Moreover I don't know...
