Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi,
I have 9 BLE devices nearby. I start scanning and all the devices displays in nRF Master Control Panel. However, the scanner then ignores 7 devices and updates RSSI only...
I'm getting the multi-link example working (device manager) with S130 SD and I noticed that the following define is in S110 and S120 but not in S130. I'm looking in the SDK8...
I've create a custom service with two characteristics. I need that the values of these characteristics are notifying at the same time. Is it possible? In this case, one of...
Peripheral role blue-tooth device, linked one phone.How to get phone address? such as phone's bluetooth mac address or something like that.Thank you!
note: device use softdevice...
Hello everyone,
I wanted to change the notification to indication for the BLE UART example when you send the message. I am currently using (and the UART BLE example is...
first sorry for my english, i work base on "ble_app_alert_notification->S110", i want to Enable Printf with uart,,,,but after i define maco ENABLE_DEBUG_LOG_SUPPORT,, 2 error...
hi all:
I want use nrf51822 to connect the some other sensor such as 90fity intelligent basketball, and discovery the service, and notify the character.
but the data...
www.microsoft.com/.../universal-foldable-keyboard
Why microsoft BT keyboard have 3 mode to support IOS, Android, Windows?
But we only have 1 sample for HID_keyboard.
Can...
HI:
I found a amazing problem:My flash project is ok,and my BLE project is ok too; But when i need to write data to flash,the BLE can't work any more.
code as follow:
all_init...
I'm using nRF51 SDK 6.0.0 and wanted to know when an "advertisement packet received" event is posted to the application. It looks like within a scan window only one such event...
Hi there,
I just ordered a nRF52 Preview DK and was wondering if this series will also be compatible with the nRF51 IoT SDK?
Anything I should be aware of beforehand...
I have an nRF51822-based device, which is a peripheral running the Soft Device s110. It has some vendor specific (custom) characteristics that are read/write. A mobile app...
Hey Nordic,
I am using the nrf51 to operate a sensor and send data wirelessly. I want to store the id of the sensor in the flash memory and I Understand that a good way to...
Hi, as I tried out the example code for PWM in SDK 9, it didn't worked for me. A closer look showed that in method app_pwm_init the method app_pwm_channel_duty_ticks_set will...