Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi!
I'm using nRF51DK with s110_nRF51_8.0.0 Soft Device and SDK_9.0.0.
My application reads ADC with frequency 500Hz (2 bytes of data from one sensor each read), and twi...
I am just wondering about the status of nrf52 support for the mbed platform (specifically as a yotta target).
I have seen a number of other threads on both the nordic side...
I am developing an application on a STM32 CPU that uses a 51822 through BLE serialization for BLE connectivity.
I have connected some LEDs at the pins of the 51822 to indicate...
Hi,
The nRF51WLCSP needs IR blocking coating and I found here that an example epoxy can be Epo-tek 320. I just want to check if there is any specific time for covering...
Hi
I have been able to successfully write using FDS but I'm unable to read back using the same keys. Here are my code snippets:
#define FILE_ID 0x1111
#define REC_START_ID...
Hello~
I'm using JLinkEXE to flash an nRF51822 chip. When I use nrfgo and press "erase all", it wroks. But after if I flash the s130, I can't erase the s130 with command...
Currently I have a few characteristics which are Authorized Read and Writes. Upon detected of the Authorization from the Central I trigger a few events such as:
Measure...
Hi !
I'm using an nRF52 on PCA10040 board and nRF5_SDK_11.0.0_89a8197. I want to run the peripheral ble_app_template with SEGGER Embedded Studio v2.20. I correctly set...
In an effort to try and determine why FreeRTOS tickles idle is consuming more current than tick mode with an idle task, see this post devzone.nordicsemi.com/.../ , I noticed...
Hi, i am designing a board using nrf51822 and planning to use a MOSFET for reverse battery protection instead of a schottky diode or a normal diode. I am new to this and learning...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I'm developing a nRF52 application that exploits two ADC channels in single ended configuration.
VDD is 3.0V.
For the signal conditioning I've chosen a driving Op...
I've been trying to get my head around using a BLE central and making connections so I've loaded up the multi-central example to figure out just how everything works. I turned...
