Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx(the send length is fixed 10 bytes) ...
Dear nordic employee:
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
When I am trying to use that file for Firmware Over the Air update feature in my application code then program compilation and all is working fine but when I am trying to...
hi all,
i have a electronic device having a button which sends continous data till i keep button pressed.
i want to send these data without losing connection.
i can across...
Hello,
I program the nrf51 in C++ using GCC and Eclipse as IDE (this question is not related to the C++ toolchain).
I was wondering if it is possible to add the extern...
Hello!
I bought NFR52 DK preview board. As microcontroller it works well. But when I try BLE examples, they do not work. I installed SoftDevice S132, downloaded ble_app_uart_s132_pca10036...
Hello!
I want to add the battery services in my nRF51822 project for getting the message of battery. Is there need battery-powered?
But,I am sorry to see that the led which...
hi everybody,
I'm working in a project, I need to establish a connection between a beacon & the mobile phone, I want to prevent any other masters of connection to my beacon...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Hi new to Bluetooth, but familiar with Radios and embedded devices
I have 2 devices that only connect to each other.
in the interest of extreme battery conservation I...
I am using a BLE UART friend module and I am trying to set the GAPIntervals parameters. I realised that when I set my max conn interval parameter above 2000ms, the device...
I am planning to use the nRF51822 and the s130 soft device to manage data coming back bluetooth sensor nodes. It is likely that there will be more than 8 peripherals, although...
The SoftwareSerial library allows GPIO pins to be used as TTL serial pins by bit banging.
The nRF5 suffers from the same problem that the Arduinos have. 1 UART.
Does...
Hello guys
I tried to start TWI bus and got a lot of questions. (NRF51 1422 AC)
I added necessary libraries, could You tell me what more i need to include in my code ...
Hi , We are using NRF52832 for our product .I have a small doubt in using GPIO . Can we use PORT and PIN events simultaneously at a time .
I need to configure some pins...
Hi,
I have three beacons in my setup:
One listening (R1) and two transmitting (T2, T3). T2 and T3 transmit packets with same length.
Say, T2 has started transmission...