During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Hi folks,
I'm having some UART trouble - help would be much appreciated, and thank you in advance.
------------------------
Overview:
I'm working on a project that...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hello,
Is there any way to configure the flash data default values during programming phase with Keil IDE?
In IAR, it is possible using a file ".s43" included in the...
Hello, I'm using the nRF51822_QFAA chip on a custom board, but the layout and parts are the same as on the nRF51822 USB dongle . I tried flashing the Board\pca10001\s110\ble_app_hrs...
I am using nRF8001 with EMF32.
inside hal_aci_tl_send function
C : 1, 14,
inside hal_aci_tl_event_get function
E : 3, 132, 128, 130,
It is looks like
Length == 3
...
Hi,
I am working on a small (1 inch square) bio-sensor project that needs Bluetooth capabilities. I like the nRF51822 and was looking into the dev board ( www.nordicsemi...
Hi
I am setting up a production programming script, and would like to know if it is possible to write short strings or numbers directly to flash. For example, i would like...
I use an ISP 130301 Development Kid for getting familiar with the nRF51822.
I flashed SD110 on the Demo Board with nRFgo Studio and compiled and loaded the proximity example...
Hi, I have a project where I need to communicate using UART BLE between nRF51822 and a PC ThinkPad with Windows 8 and embedded BLE4.0 hardware.
I have programmed the nRF51822...
I'm running into a hardfault. I perform some initialization and enter a main loop. At the end of the main loop, I put the soft device into sleep mode and wait for an interrupt...
Hi,
Recently I updated my SoftDevice on beacon from 7.1.0 to 8.0.0. Unfortunately, I met the same problem with advertising timeout which I faced with in SD 7.1.0, but the...
Hi all,
I have some doubts over the memory management of nRF51822 and nRF51422-EK.
I have gone through the link in this forum where it is explained buy I'm still not sure...
I'm trying to build a project of "nRFUART_GoogleAPI_Android4.3+" from the following link.
[https://www.nordicsemi.com/eng/Products/nRFready-Demo-Apps/nRF-UART-App2]( www...
I have one doubt after reading the definition of PSTORAGE_MAX_APPLICATIONS and PSTORAGE_DATA_START_ADDR in pstorage_platform.h and the actual computation of used flash memory...
MCU : NordicSemi nRF51822-QFAA (Using custom board)
SDK Version : 7.2
Softdevice : S110 7.1
Using IAR for ARM 7.1
Hi, I was migrating my codes (SDK 6.1 to 7.2...
I am using the ble_app_template, together with one timer called every second. The timeout handler of the timer just prints a short string on the serial port using simple_uart...
Hell.
I will use flash from pstoreage.c . but seem to only use for bondmange. I find an define:
#define PSTORAGE_MAX_APPLICATIONS 2
This is just for "mp_flash_bond_info...
