Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi.
I am using SD s110, ble_app_uart example from SDK10.0.0 on dk pca10028 as a peripheral. The central is a laptop running linux.
I am trying to establish a connection...
As noted here , a lower interval will give quicker connection - but at the expense of power consumption.
With a 4s interval, it seems that it is likely to take several...
Let's say I add two PPIs which both trigger off of the same event. One of these PPIs is connected to the CHG[0].EN task, and the other is connected to the CHG[0].DIS task...
In the GTT_2_Introduction nRF52 document there is a picture with text
-42 dB Selectivity (2'nd CI). As far as i concerned it's about Carrier-to-interference ratio. But what...
Hi.
I am using DK PCA10028 V1.1.0 for my devlopment. The SD is ver 8.0.0, the SDK is the latest and keil v5. The IC is nRF51422QFAC. I am trying to flash the examples from...
Hello, Is it possible to configure nRF's USART to work with Smartcards (ISO 7816)?
The ISO7816 specification defines the bit rate with the following formula:
B=(Di/Fi...
I use the " nrf51-ble-dfu-symmetric-signing " example from GitHub.
The application download over dfu works fine on the PCA10028 board.
But how can I install this bootloader...
dm_distributed_keys_get returns address of local variable 'peer_enc_key';
sdk version: nRF51_SDK_9.0.0_2e23562
in function ret_code_t dm_distributed_keys_get(dm_handle_t...
hello guys,
I'm working in a project & I added some sort of security to the project, I enabled the bonding & MTIM flags through:
#define SEC_PARAM_TIMEOUT 50 /**< Timeout...
Hello,
The 32kHz external oscillator is it required by S110 softdevice v8.0.0?
I haven't see this information in soft device specificaion v2.0.
Thank you.
Hi everyone,
I am using the Arch BLE running firmware version 221 (most current one).
Whenever I create more than 3 PwmOut objects (from the mbed library), the MCU just...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I think I have followed everything from:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
to convert the dual_bank_serial_s110 to an S210 serial bootloader...
Hello
I’m trying out the new nRF52832 (QFAA-AA0) with preview kit pca10036. I have S132 softdevice installed and running the beacon example from SDK 0.9.0 which appears...
