Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hello everyone ,
I have written the program for getting the buzzer Beep sound and then i compiled the program without any errors and warnings but i am not getting the beep...
I recently grabbed the latest SDK nRF5_SDK_11.0.0-2.alpha. I was looking at some of the changes and wanted to run one or two demos to make sure I was able to build them properly...
I am testing this on ble_app_hrs and ble_app_hrs_c. After devices are bound I would like to skip discovery as it takes long time. So all I need to do is get the service's...
After I receive data by ble_nuts,using example ble_app_uart.
I call ble_nus_string_send to the central, however I got error,I print error code is 8 which means "NRF_ERROR_INVALID_STATE...
hi
First,I apology for my poor English...
I want to make a project to connect 2 device.
With a sensor from TI , which comes out the sensed signal .
Transfer the data...
Hi,
platform info:
SDK 9.0, NRF51822, SD:s110_nrf51_8.0.0, Master Control Panel(android):2.0.0
We use eample dual_bank_ble_s110 under dfu/bootaloader/pca10028/ of SDK...
Hello,
I've built "bootloader" project in sdk6 and sdk8, which named "sdk6_bootloader.hex" and "sdk8_bootloader". Then what I did are listed as below:
(1)
using ...
I am trying DFU with:
BOARD_PCA10040,
nRF52_SDK_0.9.2_dbc28c9
s132_nrf52_1.0.0-3.alpha
One interesting thing is the SDK_0.9.2_dbc28c9 can not work with
...
Hi,
We currently (no pun intended!) don't have any battery protection circuitry for reverse polarity designed into our prototypes. Our device is powered from a CR2450 coin...
Dear Nordic.
I read specific data using GPIO(timer sampling), BUT, occasionally, the data is broken because of Softdevice interrupt.
So I want to guarantee it while reading...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
Hello everyone.
I would like to ask if is possible to compile and run examples from latest IoT SDK 0.9.0 on pca10028 board. Every example has only Makefile for latest pca10041...
