i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Hi,
I want to use nPM1300EK、nPM PowerUP (official v2.1.1) profiling a chargeable battery, whose rated capacity、standard charging current is 2000mAh and 400mA respectively...
Hello,
I'm developing my custom sensor application. It's a matter over thread device. Before final product I'm working on a NRF52840 DK PCA 100056 v3.0.1 and NCS 3.02. It...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hi,
I encountered an issue when trying to integrate DFU to my application. Every time I upload my application through DFU, the bootloader gets overwritten, i.e. only softdevice...
Hello,
I have to do a pre serie of a new product based on a NRF52832-QFAA.
I'm in Europe and I contacted local distributors (Mouser, ...) and there is no way to get...
Hi, when I run the ble_app_proximity on my 51822 board, I can connect the 51822 board with NRF Master Control APP, after a little while , 51822 disconnect with app, and trace...
Hi.
Is this issue resolved?
github.com/.../902
I tried lately using mbed-rtos with nrf51822, but no luck.
I would like to use threads, is there a way to circumvent...
Hello everyone,
i'm kinda new to microcontroller programming and feel like i bit of more than i can chew. I bought a variant of the nrf51822 chip ( github.com/.../Board...
Hi. Currently, i am testing the BLE power consumption on nrf52.I set connection interval 20ms(min=10,max=30) ,slave latency 0 and connection data size 20 bytes.in addition...
It seems like the IAR startup file in SDK 11 for nrf52 is older than the one that was included in the previous SDK 11 alpha
IAR Embedded workbench 7.50.3
I have a queston for softdevice S130 example about Environmental Sensing service.
I readed spec. but I can't find out any ESS profile example in SDK.
Is SoftDevice S130...
I want to use the nRF24LU1+ for a project where it will be a HID usb dongle. But I dont get which tools I need to make it. The KIT DEVELOPMENT NRF24LU1+ work for it?
T...
Hello,
This morning i did migration of my code from SDK 11 alpha 2 to 11 final on nRF52 and i have a big problem.
Nor bootloader or application do advertising. Am I...
I want to merge the softdevice and application in the makefile is it possible ?
if not possible what could be the easier way. I am using Linux OS .
thanks
Hi everyone.
I'm trying to program a NRF51822 Beacon using the nRF DK board. Of course I looked around here for advice on what type of connector to obtain.
devzone.nordicsemi...
Hi,
I have a hardware (wired) UART transmitting data to the nRF51 at intervals. I'm currently trying to implement UART-BLE that runs could concurrently with the wired UART...
