Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I am using SDK 11.0.0 and S132 on a nRF52832. In my application, my device can operate in BLE mode with the SoftDevice enabled or in custom RF mode with the SoftDevice disabled...
I need an accurate timer to generate pulses about 20ms. With simple timer this is workiong fine, but I need more then one timer simultaneously. So I would like to use app_timer...
Hi
I am working on NRF51822. I am using S120 ble_app_multilink_central example. I am trying to create a Timer1 interrupt of 1ms interval. My interrupt is working but interval...
Hi all,
I am trying to block connection from other devices to my nrf51dk board, except some specific devices. I used whitelist but it seem like the peripheral only block...
Hi,
I have just bought a nRF51822 Beacon Kit. The sticker on it shows that it is a PCA10006, Rev 1.2.0 2015.17 on it.
But I think that it is PCA20006.
What is the best...
Hi
I am getting some weird response from my nRF51-DK.
Situation 1:
When I try to flash it with the Blinky code (\sdk11\examples\peripheral\blinky\pca10028\s130\arm5_no_packs...
I'm trying to under the ble_app_multirole_lesc project and I'm a bit confused about calling sd_ble_auth_key_reply and sd_ble_lesc_dhkey_reply. If you are using Just Works...
Hi,
I am trying to send a HEX command to a device over UART at 9600bps using nRF52 DK, but it never works. However, it works with Arduino (so the receiving device should...
I have nRF52 Development Kit,after my first time programming the Firmware to my board.I can't erase or program it any more?
The nRF52 Development Kit can be connected with...
Hi,
I have read the following posts and understand how low clock frequency mode can be selected
devzone.nordicsemi.com/.../
I've also read in many posts that 4s calibration...
Dear Sir:
Could I use the external reference AREF1(pin0.06) instead of internal VBG 1.2V for ADC operation ?
I do the following settings to config using external reference...
Hi, I am using HRM example from SDK 10.0 with s130 on nrf51822 (attached project herewith). When I try to bond from Android(master control panel of Nordic), I am able to get...
100835_Rev1.PDF SRU532.pdf n5_starterkit.h
main.c
Hi,
i am currently working on the Nrf51422 chip with s310 softdevice . The problem i am facing is that when i dump...
Hi!
I'm fiddling around with the PCA10040 and the experimental_ble_app_blinky from the SDK found in examples/ble_peripheral/experimental_ble_app_blinky. I've had great...
