Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Using the nRF51422 with the TWI hardware version. Just playing around to verify signals with the following code which just configures the TWI1 and then repeats continuously...
Hi,
i tried to update the firmware of nRF51-DK but it crashed and now Keil uVision says "Cannot find the JLink version number"
Its also not showing in the nRFgo stu...
I'm developing application using your devices (PCA10001/PCA10000) and S130 SoftDevice. I tried to implement DFU/OTA feature in my app. For this purpose I used DFU sources...
Hi All,
Does anybody has a working setup using SD 7.1.0 with SDK 7.2.0, iOS 8, DFU with a secure connection?
When I use no encryption it works, but when I enable encryption...
So I'm currently trying my hand at some very simple things that one can do with the NRF51-DK.
One of those things involves sending notifications to a client on certain...
Hello,
I'm testing n51822 with low voltage mode, and want to check the BOR condition.
Is there any threshold for brown-out reset, or voltage tolerance? e.g. 1.68V...
Hi.
I have received down the source of the example of experimental_ble_app_uart in my keil.
I use register.(NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;)
but, Hardfault occurs...
Hi there,
I am currently using the nRF51 DK trying to teach myself how to create a working ble application. I am currently going through the application note nAN-36_v1...
Hello!
We are using an BLE NRF51822 chip as a GATT-Server, unfortunately without any possibility to modify its software at the moment. The BLE-setup should be very similar...
I want to run the Direct Test Mode for nRF51422 on my board, I'm trying to use the nRFgo Studio.
When I'm trying to connect to the specific COM port, I get the following...
Custom Board which has NordicSemi nRF51822-QFAA MCU,
a temperature sensor (Si7020-A10), and a white LED. The circuit follows the internal LDO setup.
(Ref. nRF51822_PS...
Hello,
i use Bootloader from SDK 7.2.0. I have some questions about init packet handling:
The bootloader compare the device type, device revision and softdevices...
During ble ADV，my device will consume 60uA，when ADV stoped it will drop to 13uA. But when I get ble connected current will up to 130uA.
I test nrf51_sdk_v6_1_0_b2ec2e6...
Hi,
in the new version of S110 (8.0.0) I can see the implementation of scan services:
SD_BLE_GAP_SCAN_STOP, /**< Stop Scanning. */
SD_BLE_GAP_CONNECT, /**< Connect....
Hi,
like many others, I'm confused with Peripheral Passkey Connection.
I'm playing with the ble_app_hrs, in order to be able to setup a Connection Passkey (for the moment...
