Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
When I tried building the Mesh 3.2.0 SDK on MacOS with cmake, I got link errors with the static libraries rtt and uECC.
The fix I discovered was to change the CMakeLists...
I am working on developing an application where the app layer tries to throw out messages if the message parameters are not valid. One the parameters to validate is a TID...
Hello, I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
Does following...
In order to compile against custom hardware, we changed overlay and dts files, but I cannot remember which. How do I find out?
I get the error
devicetree error: 'ss-pin...
I am using NRF52832 as Beacon, I want to classify the RSSI as High, Medium, Low, and Poor based on RSSI.
I am using SDK14.2.0 for Beacon and Gateway.
And using +4dBm Tx...
We are using Mesh SDK 3.2.0 and nRF52840 DK.
We wanted to use p_meta->p_core_metadata->params.scanner.adv_addr.addr as a unique identifier of the node hardware inside the...
After downloading and installing nrf mesh SDK as directed here https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK/v3-1-0/index . I'm not able to build any examples...
Hi, I am trying to use the RSSI viewer to scan RSSI values and verify the nearby beacons. But unfortunately RSSI viewer is NOT working and the following error message shown...
Hello.
I want to use the example of throughput with nRF52811.
I have changed it by looking at the nRF5 SDK Documentation, but it is not done.
(Software Development Kit...
I'm having issues building nRF5 SDK for Mesh v0.10.1-Alpha examples. On an Ubuntu 16.04 VM, I have installed the toolchain per the Debian/Ubuntu instructions and was able...
Hi,
I have two questions:
1) I am using ant bpwr tx example, SDK 15.2., Softdevice S212 v5.0.0, Segger embedded studio, nRF52832 DK and Garmin edge 520plus to display...
Hi there,
I have a custom built board with the nRF52840 and I'm trying to consistently transmit roughly 8 kilobytes per second or 64 kbits/s which seems way under the what...
Hello,
I'm working on a project that have with multirole to do, i have 3 device one act as master after a button is pressed, now i want to establish a connection between...
Hi,
I am having some issues with DFU and Keil.
I am loading Softdevice s140 v7.0.1 via nRF Connect and then programming a secure BLE bootloader using nrfjprog.
The bootloader...
