I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I am using a development board pro nrf52840 mini from Sparkfun.
I'm trying to use the TWI peripheral on nrf52840 to communicate with an external device (another...
Hello! I'm using nRF5_SDK_15.0.0_a53641a to programm my Nordic NRF52832 with Segger Embedded Studio. I'm trying to increase the BLE Tx power to 4dBm. At the moment I've tried...
1.How do I use TWI \ TWIM Read\Write in blocking mode ?
I am facing an issues with my nrf52840 based design, where I issue consecutive TWI write\read .
I am monitoring...
Hi,
Why can I no longer access firmware.nrfcloud.com as, e.g., still described in readme.rst for the http_application_update sample. I have seen that the "regular" nrfcloud...
Hello ...
New to Nordic SDK and trying to implement SAADC to read battery level. Have looked at a bunch of posts. I started with the ble_app_uart example app and tried to...
I'm new to this world of IoT. I want to use my thingy91 to monitor temperature at a vacation home, but don't need the data every few seconds. What is the best way to slow...
Working with nRF9160 in Zephyr, I've recently noticed that there are multiple conflicting definition of the errno.h values available, and I'm pretty sure I've seen both in...
Hey,
This is in relation to the errata #198 where tx buffer for spim has to be assigned its own section in RAM. I've updated the linker file to do so but I want to add a...
Hi, this problem I have met nearly, when I call mesh API to send request from client to server in light switch example (using SDK 15.2 and SDK for Mesh version 3.1.0 ) with...
I'm using: Segger Embedded Studio 3.52, nRF52840-PreviewDK, nRF5_SDK_for_Thread_and_Zigbee_v3
Is it possible to restart the Zigbee stack without restarting the whole chip...
Hello
Development environment: mac
h/w nrf52840 dongle connected via usb
compiler: gcc-arm-none-eabi-7-2018-q2-update
Updated nrf5sdk/examples/ble_peripheral/ble_app_blinky...
Hi team, there is nRF52840 and STM32 connected via UART. I need to update ST firmware over nRF. I managed to send stm32 .hex (FW intended for ST) over nRF DFU service and...
Hi there
In the service UUID 0x2A00 I am currently trying to set a device name >31bytes with sd_ble_gap_device_name_set(). I am using the Softdevice S132 V6.1.0.
According...
