I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Good afternoon,
I'm developing my application based on nRF52840 and S140. What I pretend to do now is to make it possible to update device software (softdevice and/or booloader...
Hi,
The buttonless DFU example mentions support for S112, S132 and S140: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_buttonless_dfu...
I'm new here to play BLE mesh network. I got 4 nRF52840 DK, I am woundering how to set up a mesh network step by step? What kind of exmples(ble_app_blinky_c, or something...
Hi,
So we have a smart light control app, and it is based on nRF-Mesh-Library version 1.0.2. Since it's announced the version 1.x is no longer being maintained, we want...
I had a problem setting sniffer.
I use PCA10040e (nRF52810) V0.9.0.
I installed everything.
And copied file and folder to this path.
C:\Program Files\Wireshark\extcap...
Hi,
I am a beginner in ble and I am trying to understand the technology. I am trying to write to and read from FM24W256 FRAM through I2C. The reference I have considered...
Hi,
I checked " https://github.com/NordicPlayground/nrf5_clients_for_nrf91_network_service " firmware of nRF52 which works as client for nRF91.
But I can't find firmware...
Hi,
We have below questions regarding HFXO.
1.> Will softdevice or nordic HW be able to recognize that the 32 MHz crystal is non functional during run time (after the...
Hi,
I'm trying to flash the secure_bootloader example onto a nrf52840 DK, after generating a private key, flashing with SEGGER embedded studio worked, the device entered...
I have 2 questions, both related to power/current consumption.
My setup is a custom board, with mfw 1.1.0. I havev arlier seen current consumptions in the µA-range. I now...
Dear Nordic Support,
I am doing some test on the Thingy:91 v1.0.0 in Vietnam. I am running 2 examples: Asset Tracker with NB-IoT + GPS and GPS .
When I use the stanalone...
Hi,
How i can make the low power node to wake up until get acknowledgement . Please tell me how many ways we can try...In my project i used initiate_friendship() function...
It appears to me that the zb_zdo_ep_resp_t struct is missing a variable value attribute since the actual list of end points is missing. Should it not be similar to zb_zdo_match_desc_param_t...
