GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I have to folders with different versions of the nrf library installed (1.0.0 and 1.1.0-rcsomething) The dts and overlay files are identical in the 2 folders (nrf9160_pca10090ns...
I have taken a new Thingy:91 out of the box, fitted ibasics sim card and been through the registration process. Sim registers fine, but the 'add new LTE device' does not recognise...
Can you tell me which Heart Rate monitor gives 0x2A37 is the UUID for the Heart Rate Measurement characteristic. The heart rate service is 0x180D. Battery service is 0x180F...
How can I add debug and release configurations to the "mqtt_simple" project?
Video tutorial "SEGGER Embedded Studio - Build configurations" does not show this important...
Hi Devzone!
I'm using nrf52840 custom board to launch iot service.
We have two type of devices. One is master and the other one is slave.
For now, both of them...
In nRF5 SDK 16 (downloaded file nRF5SDK160098a08e2.zip), the components/boards/pca10059.h file is missing the LED_START and LED_STOP defines that are present for other boards...
Dear Nordic,
I have a 4MB external flash on my board, I've successfully run the code on it by using XIP. However, I got stuck when I was trying to read back data from...
The bug shows when executing an application in RAM with nrf52840. Using SDK 16 but seems to show in older versions also.
The below function code is the first level of...
Hi all!
Everywhere it can be read how important the dimensions of the groundplane are for a well working antenna... but what are the right dimensions? And where is the best...
Multilink S132 central should handle connections to multilink peripherals which do continuously advertise. Once central got first adv event from such peripheral it establishes...
Hey,
As a student currently I'am working on a project for my universitiy. I want to use the nRF51822 for Bluetooth low energy communication.
In the datasheet is written...
Hello Everyone,
I'm involved in a project where we are evaluating ble mesh and Thread mesh on nrf52840.
I want to know, does Nordic supports ble mesh and Thread mesh simultaneously...
When using Keil Compiler, I am unable to compile any of the ble_peripheral examples. I get an error that says...
RTE\Device\nRF52832_xxAA\system_nrf52.c(29): error: #5...
Issue with NRF52832 Firmware installation
Hi We are developing custom boards with nrf52832 chip, and it is working well.
The issues occurs when installing firmware without...
Hi,
as i mention in https://devzone.nordicsemi.com/f/nordic-q-a/44924/dfu-serial-failed i have f ramming error now and then when i do DFU over serial.
My idea was to write...
