I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Halo, is there any linux ( possibly debian or even better raspbian ) driver for
nRF24AP2-USB dongle?
Do you have ANTware II linux ( possibly debian or even better raspbian...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I'm using Keil to debug my application. Softdevice was loaded w/ Studio and when I click on Debug Keil loads the code but it does not stop at any breakpoint I set. It does...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
First I'm new to these devices and BLE in general.
I am however very experienced at embedded design and Keil tools and ARM processors.
I have got the demo heart beat...
I have the ble_app_hrs communicating with the ble_app_hrs_c, and everything works OK. However, I have to be able to send data in both directions. How do I modify, or what...
I am developing a device converting adc input into data and transmitting them and receiving them at other place,I cant figure out between analog input eg:AIN0 and the port...
Hi,
I'm using nrf51822 with s110 softdevice v6
My question is the following.
How many devices sending advertising messages can be detected at a time by a central unit...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi All,
I am trying to run the uart example that comes with NRF51822 development kit. I've set up the mother board (nrf6310) according to the sdk doc and have flash the...
Dear Nordic Developer Zone,
I am using nRF51822 with softdevice.
I don't understand very well the advertising mode "whitelist".
My target is to be able to connect...
Hi all!
I'm running my code based on example "ble_app_template". When advertising without doing anything else, the current comsuption is about 200 uA.
Then I added a...
Hi,
i just started again working with nrf51822 but now with eclipse+gcc and with new soft device S130.
I am struggling with the addresses of flash and ram. I want to...
