The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I updated my MCP to the newest version and then the new MCP wanted to update the pca10000 with the newest firmware--> failed. Now i can't get my pca10000 to work again. i...
Hi,
i am trying to connect via bluetooth using the gatttool on a Raspberry Pi. On the Nordic device I am using the BLE Proximity Demo. Everythings work fine, but after 30...
Hello all,
I am trying to get a communication between the nRF8001 and the nRF51822 using the UART service. The nRF8001 is connected to an Arduino and is working fine. I...
I am trying to find out the issue with my nonvolatile driver. I currently try running
nrf_nvmc_page_erase((uint32_t)(page_address));
However, that doesn't seem to...
I've been testing Pre-Production samples running a firmware in which I catch any and all Error codes or Reason reasons and write them to the gpregret register to be read later...
Hi, I am using a modified version of RBC mesh.
When I connect with an external device to one node using BT I get connected but I can get randomly disconnected when data is...
So, I'm trying to work around the Ble Uart example, using the PCA10003 Board. The example uses one of the buttons as a "Wakeup" source, but during the bsp_init() call, the...
Hi Nordics,
I would like to run the app example “ble_app_hrs_s110_hci_pca10028 (nRF51 PCA10028)” on the 32 MHz crystal. Can anyone help to change the code to 32MHz base...
Hello,
I am currently use the new SDK 8.0 for the NRF51822 (S110 soft device). I noticed that on SDK 7.0 for the ble_gap_sec_params_t struct , there was a variable called...
I want to see register values in interrupt service routines after a timer timeout. However, when I enable debugger in Keil, it only iterates once to the end of main function...
I've been trying to get a simple blinky program to compile for the better part of a day now. The makefiles are outdated and so are the keil projects. Is this SDK no longer...
Hi ,
I have a code like below.
__attribute__((used, long_call, section(".data"))) void function_1()
{
unsigned int a;
unsigned int b[10];
int c;
c= a-(...
I currently have an application with DFU bootloader that runs on s110 5.2.1 on a rev1 nRF51822. If I upgrade to the latest rev3 chip, can I just flash it and everything will...
