Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
Hi.
I am looking for the internal resistance of the ADC pin of my nrf51822. I have looked at the Product Specifications (as well as the Reference Manual and other documents...
I find it unstable to send hid data, even if I set timer 1 every 8ms to send hid data.
I can catch data bag from wireshark it seems that interval of two data even close...
Hi All:
The hardware is working perfectly up until I changed some codes in the program and load it on the chip then I am unable to program again. The error message is:...
1.Size of EPROM. Is it big enough for our program as well as our data file for the whole day?
2.How can we secure the EPROM so that no one else can overwrite our code or...
We have an application that is an apple ibeacon, plus some extra properties that can be read (battery level for example)
The "ibeacon profile" eats up all the space in the...
Hi Guys,
i'm a newbie, trying to get the heart rate demo project working.
I've connected the nRF8001 to my own hardware, using a PIC processor.
i'm able to connect...
Hi,
I have a question about the service profile (ex:heart rate service, battery service,etc...), these services are based on protocol of IEEE11073-20601? Actually, I want...
See subject. The softdevice is currently installed on the chip (v6.0.0-1.alpha)
I searched online, and found some information that the security state of the chip has been...
Hi all,
When I receive data from the phone app, I do it via this service handler (and it works):
err_code = ble_services_init(&my_device_service, ble_receive_handler...
error:-559038737 ...line:1128 file_name:src\ll_lm.s0.c
And I can't find this file, so can somebody help?
Why this happen? How can I do to avoid this？ It will cause reboot...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi
I would like to use the arm based energy micro MCU to update 51422 via UART
I've understood how the firmware update example with hci, but I need a set of hci api to...
Hello,
I in the nRF8002 data sheet it mentions a Programming tool for the nRF8002. Can you please send me the partnumber of this tool? Also, if a programming house wishes...
"Install the Master Control Panel and the nRF51822 Development Dongle (PCA10000)
Download and install the Master Control Panel from our website. Make sure to select...
