Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi
I'm trying to run the HRM_RX exemple on the nordic NRF51422. This is my configuration:
-Eclipse IDE
-ARM GCC 4.8.3
-NRF51422_AAC0 so I'm using the lasest SDK 4...
hello,
i am trying to use the example for the ble_lbs from github.
I get no erros on compile and flashing.
But wenn i try to see the device in the master control panel...
I've been slowly and incrementally adding changes to the ble_app_multilink_central example from nRF51-SDK-6.0.0. This is an exercise to understand where my other app stopped...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello everyone!
Firs of all consider I'm very new in micro controllers programming/debugging, so your patience would be much appreciated.
I have a nRF51822 mKit like...
I use multilink_central example and try get information about discivered service:
APPL_LOG("[CLIENT_LOG]: Count of services: %d\r\n", p_client->srv_db.srv_count);
APPL_LOG...
my led connect whit a pin like this:
the led positive connect whit VCC and the negative connect whit a pin through a resistors.
when I config the pin as a output like...
using the nrfGoStudio to program s110_nrf51822_6.0.0_softdevice.hex
Tools:
Jlink,SWD mode as the figure:
but there are some problem
1:we can download demo BlinkLed...
Hi,
I need a RTC calendar ble stack on nrf51822 .
(turn on the RTC0 on ble stack and get the count, how to setting the rtc wakeup )
which calendar need follow :
track...
Hi,
I'm trying to get a time stamp using that kit, but I'm having problems doing it because always I upload the code to the kit, it stops working.
I add here the code...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
I would like to use nRF51822-based BLE module as Master role or Slave role.
How do I give role(Master or Slave) to nRF51822-based BLE module ?
What should I use ?
I ask...
