Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
Hello,
I am trying to remake an nrf52 project in Keil and ran into a problem regarding stdint.h. There is already an "include <stdint.h>" statement and Keil has not reported...
Hi,
I am testing the NUS using the UART example in the SDK11 with the PCA10040 board.
Since I want to achieve the maximum speed of transmission I used the FIFO buffer...
I am having issues waking up nRF52 with s132 using the RTC interrupt. The same code is used on nRF51 with s130 and does not show this behavior.
The RTC is configured and...
Hi,
is it possible to have the same configuration as in the example ble_central_and_peripheral but with ant+ as peripheral (on nRF52)?
Thank you for your attention
I am doing externally triggered SPIM transfer on the Nrf52 using PPI.
I found that the NRF_SPIM_TASK_SUSPEND is a very power hungry operation as SPI suspend waits for the...
Hello
I have a nRF52-DK and I am trying to programme an external designed by myself but this one contains the nRF51422 chip. I am using nRFGO Studio to upload the .HEX...
I consider using " nRF OpenMesh " to implement my project.
But, I have no idea bout what's the throughput of it.
Anyone has an idea?
I find the max. content of advertisement...
Hello, I'm trying to make two nRF52832 connect to each other on their own. Currently, it seems that the ble addresses are reversed when printed by ble_gap_addr_print in different...
Hello,
I'm looking for a solution to achieve best possible resolution timestamps of received advertising packets for BLE. Is there any specific chip that you would recommend...
Hi there!
I searched the forum and didn't find any clear answer.
nrf52 programming pins are SWDIO and SWDCLK and chip can be programmed.
When nrf52 is part of a pcb...
HI,
I am trying to Port the BLE BEACON source code of PCA 20006 to PCA 10028 EK.
I have changed the IROM settings.
I have initialized the soft device handler to NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hi,
I am trying to understand how can I have a running counter based on the low power 32.768 KHz oscilator that does not trigger any timeout interrupts (I am using the soft...
Hello,
I have a nRF52 to nRF52 connection. I want to secure it (auth and if possible encryption) with a pre shared key. What are the points that I have to modify please...
