Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
What will be the price of nrf52 chips compared to nrf51?
Will there be any cheaper version of nrf52 chips with limited capacbilities (e.g. less flash, ram)?
I was trying to setup a GNU toolchain on Windows and use the nrfjprog utility, but despite having installed the J-Link drivers (4.78), nRFGo Studio as well as the nRF51 SDK...
I cannot seem to get pstorage working using the S210 softdevice. I can get it to work using the S130. I was not able to find any info on pstorage using S210.
I used the...
Hi
I want to use the nRF51822 to do the BLE product.I have read the datasheet of nRF51822.I have some questions:
1、Can the I/O of nRF51822 support 4.5V~5V input?
...
Hi All,
My goal is to change the advertisement(when not "connected" to ble device) in every SPI Interrupt, depending on the data received i set corresponding data in advertisement...
In porting over my project from Keil to GCC using SDK 8.1.0 I can build and run just fine when I build with Keil but when I build with GCC and try to run sd_softdevice_enable...
Hi,
I trying to write an application with android for my nRF51822 device
I use Battery service example but every time i update battery level i need to request for changed...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
Hi,all.i want to run DTM on pca10028 develop board and connect it to my pc via USB (JLink CDC UART Port) on the board.My pc operation system is ubuntu10.4. what is the port...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,all. i run example.py(nAN34 document) on ubuntu10.4,then get an error:
./example.py:line 13:unexcept error near "(";
./example.py:line 13:'def main():'
what's wrong...
Hey there,
I am having issues downloading the SDK for the NRF52. It just goes to a blank part of the page. Is there a better way for me to get a hold of this SDK?
T...
So after reading some material it seems like I can pretty much define which pins are responsible for I2C communication. Is there any limitation to which pins I can set? Does...
Hello,
There are many anomalies in the NRF52 Revision Engineering A (QFAA-AA0, QFAA-AC0) .
This revision it is the current chip?
If so, do you know when there will...
I am trying to build the "Getting STarted" example app. I got it to work with Keil. Now trying Eclipse.
I got all the includes in the project set up and these all resolved...
