Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I run a laptop which previously ran this fine on Windows 7 x64. I now run Windows 10 x64.
I cleaned out j-link, nrfgo studio, libusb etc and reinstalled nRFgo Studio again...
I know that it is possible to make 4 PWM outputs, but I need to generate 5. I will be using SoftDevice 110 and BLE. Is there any possible way to generate a 5th PWM output...
Hi,
I need to interface a LED driver (PCA9632) using TWI.
In the TWI APIs I can't see any way to pass the slave address to the TWI instance. Speaking about the nrf_drv_twi_init...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hi, I have an nRF8001 on a Red Bear Lab BLE shield mounted on an Arduino Uno. I'm using BLE to trigger the execution of potentially long running (well, a few seconds anyway...
Hi,
I've done a fair amount with the NRF51822 and Keil on Windows but decided it was time to switch to my native Mac instead of the VM!
Reading all the guides around...
Hello everyone,
I'm a beginner and i'm trying to debug a nRF51422 BLE project.
The SoC is supposed to wait for commands from a STM32 in order to execute some functions...
Hello,
I'm a newbie in this area, and I'm trying to program NRF51822 QFAA on a custom board according to the given tutorial for a dual bank bootloader ( devzone.nordicsemi...
Hello,
Since I am still a little confused, could anyone tell me what S110 and SDK I should use for nRF51822 QFAA? ( infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
i am going to buy nRF51822beacon but i do not know what to buy with it ?
i will buy nRF51 DK but i also want to use a segger programmer with nRF51822beacon.
what confusing...
I was wondering if you could advise me on the best way of adding in BLE functionality to an existing ANT application. Is it simpler to have both transmitting at the same time...
Peripheral receives 4 bytes from central in order to set color of 5 LEDs (1 byte command type + 3 bytes RGB data). There's an iOS app with color picker where user can select...
hi every one.
I need to load softdevice to nRF52 preview DK before execute this app follow it, but i don't know exactly how to do it.
This is my solution:
open...
Hi,
When I reset my nrf51822 beacon firmware using nrfgo, it works just fine. When I try to reset the firmware using jlink, I end up having problems. There are no errors...
Hello, I have downloaded the nRF_MDK_7_2_1, and open \Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001\s110\ble_app_beacon\arm\ble_app_beacon with Keil_v5.
I set IROM1...
