Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
I'm playing with the SDK 8.0 HRS peripheral example.
There is a config folder that contains device_manager_cnfg.h. But this isn't being built into the project, the version...
Hello,
I am currently trying to write my frist few lines of code.. I started with the ble_uart example and then mixed in some code from the spi_master example.. I wanted...
Hello,
why did you chose to remove the S130 1.0.0.3-alpha from the relasenotes and merge it with the latest version? I don't think that's the way it works. Now we have...
Hi All !
I was read many posts about this function and do not understand how to check if all data is deleted.
In my situation I do:
Start advertising for bonded...
My devices in the field have firmware that saves an error code when it gets thrown and then sends it to a central so that I can see if there are errors with devices in the...
Hello,
I am using the sd_flash_write function. If I use this function without the nrf_delay_ms() function (see code below) the data is not being written.
sd_flash_write...
I would like to know if it is possible to log realtime sensor data to flash while advertising. I would like to have a device which transmits real time ECG data over ble UART...
Hi
I am struggling to change the device type on examples setup for nrf51422 to nrf51822.
If I change the setting in "options for target"/device I get the failure message...
I changed the multilink central example to some custom code. However, it seems like I've run out of space. But I don't under stand how this is possible because I selected...
Using gcc-arm-none-eabi-4_8-2014q1-20140314
Using nRF51_SDK_8 Using nRF51 dongle
Build in nRF51_SDK_8/examples/peripheral/blinky/pca10031/s110/armgcc succeeds...
Hi there,
When i disconnect the keyboard, the nrf51822 will restart advertising in directed mode.
And then on_adv_evt() will receive BLE_ADV_EVT_PEER_ADDR_REQUEST event...
Hi,
I want to use BLE for following situation and I wonder if it is achievable.
I have a 3 boards with nrf51822. Two of these boards have mpu6050 sensors connected to nrf51822...
Hi,
I am a little confuse at the moment and wondering if anyone would have any insight on the matter.
I am making a pair of device with s110 and s120. So the s120 will...
Hi,
I'm trying to write my own application based on the ble_lbs example on nrf51822. Recently I've discovered a problem with reconnection to the beacon. I can successfully...
So, we have been developing our firmware (for a while now) against a SoftDevice version called 6.0.0-1 alpha. We are getting close to production time, so we wanted to switch...
