I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I have been using nRF Toolbox –DFU to reflash my project. I am using an Android tablet version 6.0.1. This process was working very nicely.
On 2/5/2020 the tablet updated...
Hi,
I have a really hard time with nRF connect. I wrote a simple app for my Dongle and when I want to program it via nRF connect it says that Device not found due to failure...
Hi,
We're trying to add a custom service to the HID keyboard example. the service is initialized we can see the service when connected to the device from the nrfConnect...
I tried original ble_app_hids_keyboard_pca10040_s112 example, then modify it by moving the code for typing h.e.l.l.o from Btn 1 to Btn3, and all possible combination of sd_ble_gap_disconnect...
I've tried using LESC without bonding, but iOS displays a pairing dialog. I don't think it is possible to avoid this, so the only way to avoid the pairing dialog is to use...
We are using nRF52832 to develop our product with the ANCS function.
But after bonding with the iPhone and then restart the iPhone, an error message "NRF_ERROR_BUSY" will...
Hi,
I've setup nRF Connect SDK v1.1.0 and I was taking a look at the the peipheral_uart example. I couldn't find any API reference when I searched in the v1.1.0 documentation...
Hello,
I sae that there is the possibility to upgrade the modem via FOTA/OTA application (for example asset_tracker), now without touching the modem could be possible to...
Hello,
Are there any hardware constraints or hard forks in putting an older version of an SDK, such as v11.0.0, on a much newer chip?
I'd like to port SDKv11.0.0 to...
Hello,
Is there any existing firmware where the nRF9160 can act as a coprocessor -- accepting AT commands and the ability to forward LTE data to and from a host application...
Hello, i am a beginner, i am parsing a dimming example. i have two client and server boards, as well as an nRF Mesh application. I can change the brightness of LED by pressing...
Dear Sirs,
I have dveloped application based on the ANT rx HRM example and with nrf52 SD board works perfectly (pca10040(
I would like to move to this application into...
I am using ble_app_gls s130 SDK_11. Is it possible to have pairing with static passkey without bonding? This is because the nRF device will be connected to different smartphones...
I am working on the nr sdk for mesh application,When the nodes conncted to the network , it needs to configured before using nRF mesh app ,My device also configured through...
I am using nRF52840 with nRF5 SDK for Thread and Zigbee 1.0.0 on the nRF52840 development kit.
The Release build of the mqttsn_client example compiles and runs fine.
Using...
