Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
In the data sheet of SHT21 is this the formula to calculate the temperature:
T = -46.85 + 175.72 * temp_data / 2^16
temp_data has the value 26'464.
The result should...
Hi,
I'm trying to define a new service, and on the GAP settings, I would like to advertise my service, but I get an error message: advertisement packet too long.
What...
I have a temperature/humidity sensor from Sensirion. The Type is SHT21x. The sensor has I2C so it should be able to tranfer the data from the sensor to the Nordic chip over...
Hi,
I am attempting to get the ble_app_beacon example working with the s130 softdevice instead of the s110. I am using armgcc and the v8 sdk softdevice headers on a pca10031...
Hello, I have inherited a project from a departed employee. I have a requirement (based on a stated desire from her to my project manager) to "bring the SDK and/or SoftDevice...
Hi,
I am using the nRF24L01+ evaluation kit in a project. Through the EV KIT software I am able to configure the nRF module in receiver mode. I can even see LED 2 light...
Hello,
I am trying to modify the ble_app_uart example from the S110 to the s310 softdevice. I am using the project from nRF51_SDK_8.0.0_5fc2c3a.
I modified the Paths...
Hi,
We are planning to design a custom based on nrf51822 with 1.8v power supply. we just want to know is there any restriction towards accessing peripherals on chip like...
I don't understand how the numbers in the nrf_pwm_init are calculated. Specifically these:
case PWM_MODE_LED_100: // 0-100 resolution, 321Hz PWM frequency, 32kHz timer...
I'm trying to repeatedly toggle a GPIOTE on every CC[0] compare within the time period set by CC[1]. CC[1] runs multiple times. Every time CC[1] is reached I want to stop...
Hi! I am looking into your products, and wonder how the workflow is.
Let's say I get the nRF51 DK to develop something reading from a sensor and sending data.
The DK provides...
Hi,
Through this post I got an updated bootloader for the nRF51822 128Kb chip version:
devzone.nordicsemi.com/.../
After the last update of the iOS nRF Toolboox Version...
I got an easy but fundamental question: How to make sure that the central sees the advertising package of the peripheral..
For example when the peripheral advertises only...
