I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
I use the nRF52840 MCU and SDK 16 with S140 softdevice. I want to use spi interface to control 3 SPI slave. They share the same SCK, MISO and MOSI. I use 3 chip select pis...
We're using the IOS-Pods-DFU-Library on an iOS13 iPhone connecting with an embedded device that supports Nordic NRF DFU. We're experiencing some issues with both the nRFConnect...
I have questions related to use of UUIDs. Any help would be grateful.
The following are the UUIDs that are seen from our peripheral device during advertisements and after...
Hi,
I tried to use the exactly same code in the TWI scanner example for nrf52832, SDK15.3. Everything works fine when I flashed only the example code, which has no softdevice...
I am looking for an updated schematic for the PCA10059 v1.2.0. Everything on info center is version 1.0.0. Noticed that a resistor was added (R7) so wondering if there were...
I'm trying to debug issues in my application related to FDS garbage collection.
My application periodically runs fds_gc() from startup. At this point, garbage collection...
Hi
I got a nrf52833 dk and followed "nrf52833_heart" SDK file readme file is success
next step I install segger studio and JLink_Linux_V662d_x86_64.
wend i open studio...
Hi Devzone:
I saw two functions to write the retention register for DFU, nrf_power_gpregret_set and sd_power_gpregret_set.
What's the diffrence between
nrf_power_gpregret_set...
I'm experimenting with multiprotocol support on a PCA10056 (nRF52840) and the S340 softdevice. I need to use BLE and ANT+ at the same time, sending data to either ANT+ or...
What type of cable is required for the debug out, P19?
The specs for the port only say the number of pins, but not the pitch https://infocenter.nordicsemi.com/topic/ug_nrf52840_dk...
nrf52840 packet transmitting time measurement for TOA or TDOA
Hi I’m cu rrently working with the given nordic project “ nrf52-ble-long-range-demo ”
What I’m trying to...
Hello
Where is the the timeout for the Resolvable Private Address (RPA) defined?
only possible in the central?
can I change the timeout in the android nrfConnect...
Hi,
I am using nRF Connect (Desktop) v3.3.0 with a nRF51 dongle with the latest firmware to test my BLE device application.
My application contains 1 customized service...
Hi all,
My goal is to store large data which is approximately 300KB and send it using UART. To do it, I think I should the library of NVS on zephyr. I achieved to use it...
Hi,
I am trying to make a design for the m odule ISP4520 from ISP, which is basically a pcb with a nRF52832 and a lora radio.
However the processor on the RF52832 is not...
