Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
This post is not a question but a result of my analysis and so a answer to the above problem.
I tried both the Simple Uart Example from the Sdk 6.0.0 (Uart without interrupt...
Hello,
did someone made Altium footprint for J-Link Needle Adapter or managed to find it?
www.segger.com/.../J-Link_Needle_Adapter.pdf
I am planning to make PCB using...
Thanks to this post we can find USB port number of all segger devices connected.
But, as commented:
If I have both the dongle and the dev
kit (plugged to the PC...
Hi all
We use an external 32MHz crystal for the nRF51822 and set the register NRF_CLOCK->XTALFREQ to 0xFFFFFF00 according the reference manual V3.0, chapter 13.3. Afterwards...
I work solely under linux so need tool to generate init packet for DFU.
Is there existing tool/script for that under linux ?
(or plan for next sdk)
Thanks
Hello,
I want to send some data via the radio and then turn the radio to receive data. For the receiving, I need to setup a timeout. I would like to keep the timeout as small...
Hi, at the moment I'm learning about NFC and I don't know much about it. But I have question. Is it possible to use nrf52 NFC only for Bluetooth pairing purpose or can I use...
Hi,
I was trying to make nRF8001 peripheral device advertise the services and try to connect using an Android device that is having Nordic Master Control App.
I have...
Hi,
I manage to get pstorage store and load work, now I am trying to update the pstorage block that I just store/load from,
the error from pstorage_update return error...
Hi,
For our current application we are using NRF51822, SDK 6.1, Soft device s110 ver 7.1.0.
In our application nRF is configured as SPI Slave and another controller as SPI...
Hi expert,
I am developing 51822 under SDK 6.1, and we have one button and some sensors' interrupt lines as input GPIOs in our platform. In my code, after calling gpiote_init...
Hi there,
I am trying to send six 20 byte packets per connection interval. Is changing the length of charecteristic simply
attr_char_value.init_len = sizeof(uint8_t...
I have set up a board using device_manager_central to connect with BTLE sensors. I have used a combination of the multilink example and the heart rate collector example along...
Hi,
I used nrf51822- EK board.
GATT - s110 6.2.1 softdevice
I transfer data through UART for nrf51822-EK(PCA10001).
But this time. I used nrf51822 smart beacon...
I develop with nRFgo SDK 2.3.0.10040.
Normally PRX can communicate with PTX by auto ACK, but when there are two or more PRXs with same configuration exist, once PTX sends...
