Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I'm looking into using the CMSIS RTOS on the nRF51822 with the S110 softdevice which I've used successfully with other Cortex M0 MCUs. I realize the S110 isn't well tested...
Hello,
I am new to BLE shield and arduino stuff. I am working on a project where I have to send the sensor data i.e. temperature sensor, humidity sensor and pressure sensor...
Hi,
I'm using the nRF51822 and pCA10001 as SPI slave.
For reasons beyond my control I have to read the Rx Buffer before the CSN is released.
Yes, I know I shouldn´t do...
Hi!
Could I find somewhere (I was trying in Nordic docs and in previous posts but everything refers to previous versions of softdevice) how to perform bonding with key...
Hello,
When designing a 4 layer board with the nRF51822, should I connect the chip and impedance matching circuit to analog ground and keep the other digital chips isolated...
use nRF51822_Evaluation_Kit
I want to auto bonding by peripheral ,once peripheral connected with center(android app).
Is there have any API to send pairing request?
Hi, I tried uploading the example code from \nrf6310\spi_master_example to nRF51822 evaluation kit board, but no matter what I do, I always get SPI error. Not compile or upload...
Hi,
is there a nRF Master Control Panel equivalent App for iphone?
I'd need an app where I can set custom characteristic. The background is to update the device using...
I'm a begginer in embedded program. I have a mbed HRM 1017 that
is pin-compatible with Nordic PCA10004. .
I'd like to make a simple app to print out "Hello World" to terminal...
Hi guys,
How to update softdevice on mBED nRF51882 kit?
Details:
I have couple mbed dev kits with nrf51882.
I use Keil for development but will move to GCC after while...
Hello all,
I wanted to ask if there are any cad files for Eagle or other hobbyist level design tools for the nRF51 chips before I spend time to create and debug them? ...
hi guys,
I'm pretty new to nordic ble development, but I have a fair idea of the differences between EK, DK and the mbed enabled MKIT.
I'm trying to build a deploy about...
I have been following this post and pure-gcc to set up my eclipse environment in ubuntu 14.04. Thus far everything works well except i cant figure out why the softdevice is...
Hi,
I made own board based on the dev kit board with PCB antenna.
I flash SD110 6.0.0 and then I load bluetooth_hrm demo and there are no errors, but I dont see Bluetooth...
