Beginner here .. steep learning curve for Nordic ... trying a project with I2S. Took half and hour with an ESP32, but many many hours later, no joy with Nordic.
Working...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
Dear Nordic.
I have used to nrf51822 custom device. I confused it because of Uart RX data.
The master device sends blow raw data to client device(nrf51822 custom device...
I'm trying to compile a program on mbed for a BLE Nano, which uses the nRF51822. I've included the nRF51822 library by Team Nordic that's listed on mbed's library wizard and...
Hello
i am trying to upgrade from sdk 9 to sdk 10 .zip version but after installing when i open some examples it asking me to install arm cmsis 4.5. pack and device family...
Hi can anyone guide me in configuring the peripherals of nrf51822 before putting the chip into sleep? For example, timer, i/o pins, etc... which is not needed to reduce the...
Hello, please help me to find nRF52 datasheet, in which are recommended WLCSP footprint, and of course schematic drawing of this module. In your Dev Zone I found only QFN...
Hi,
I'm wondering what speed the NRF52832 radio is clocked at internally. is it the main 64MHz clock or 16MHz like the NRF51?
The reason I'm asking is that I would like...
I'm using nrf51 with 16kb memory
I know that there is a region for softdevice, region for the bootlader and region for the app code and a free region
my questions :...
Hi Nordic support,
I'm pretty new to BLE and I have a system based on the UART example.
On the nRF51-DK, a modified BLE UART Peripheral example using SDK 10.0.0....
Hello,
I am working on S110 v8.0 softdevice and SDK9.0 and need to implement whitelist in our application. I am referring to the ble_app_hids_keyboard example project....
I'm attempting to download and install nRF51 SDK from here:
developer.nordicsemi.com/
Note: The links are ABOVE the masthead of the page (very poor layout!)
I...
Hi everybody,
Here are some related questions based on the same bug :
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I build a test application...
Say, for example, I have a BLE peripheral programmed with S110 on nRF51822. When an Android app connects to it as a BLE GAP central(and becomes GATT client), can any data...
I am trying to get the Device Format Update tutorial to go, but run into a problem while I am programming the using the nrfjprog routine, and the programmer aborts without...
Hi,
My bootloader code was modified to include the device type and device revision when performing the OTA. I used single bank example.
When I made the zip for OTA,...
Hi,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0.
I received BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST event after setting HRM CCCD...
