Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Good morning,
my problem is that this module has a very short range.
The maximum range that I found was 4 meters.
Have you any solution for increasing this range?
Thanks...
Hi,
I saw several structs that you have in your library and I am curious as how you are forcing the alignment, since I want to do the same.
This is one of them:
typedef...
We are currently working on NRF52 DK.
I know that a Segger RTT is used to print the debug message using a Real Time Terminal(like TeraData or Hercules).
I know that...
Hi :)
I developed my Bluetooth app with MBed and the RedBear BLE nano module. My jumper wire installation connecting an stm32 with the module is working great and everybody...
Hello,
what is the initial output state of the comparator in single ended mode, if the input voltage is between the upper and lower threshold?
Is it undefined, always...
Hi,
I have a question regarding the nrf52 UARTE driver. I have the basics setup and working, I can send and receive data using the UARTE.
What I need to do now, is find...
Hi all,
Someone, please, can give me an information about programming a board nrf52832 using the pin SWDIO/SWCLK.
There is an application note that explain this topic...
I don't know where to submit these things.
I don't fully have my DFU working yet, but clearly I have a badly formatted init packet. However, the resulting behavior was...
If an app is advertising on all channels, and receives a SCAN_REQ on 37, will it transmit the ADV_IND (and potentially SCAN_RSP) on 38 and 39, or is advertising interrupted...
I am attempting to use sscanf() on nRF51822. However the chip simply freezes when reaching that part of the code. Do I need to add anything in the toolchain to make it work...
I'm using nrf51, I noticed that when I disable some functions calling (in the file flash_memory_management.c ), the behavior or the function in the file ( fatigue.c ) is correct...
Hello ,
Easy question, I am using the nRF52832 and am trying to find out if all gpio pins have gpiote functionality? And if so can all gpios be configured as an external...
hi
this is my timers_init(); func
static void timers_init(void)
{
uint32_t err_code;
// Initialize timer module.
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS...
