hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I want to request AGNSS information from nrf cloud services using my nRF9151DK board. As a first step, I flashed the nRF Cloud multi-service application onto my DK...
Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
Hi.
I'm using nRF51822, SDK10.0.0, S130.
I made "radio test" program as below at the first.
void radio_tx_carrier_test(unsigned char freq_ch)
{
NRF_RNG->TASKS_START...
Hi,
Can we add device address with all fields set to zero's to whitelist.
I went through the spec, but it doesn't talk about the address set to zeros.
Thanks,
r...
Is it possible to change data send in scan responses after each Advertising Event? I know that sd_ble_gap_adv_data_set() has constant input arguments, but it seems weird for...
Hi everyone;
Im trying to use my nrf51822 as iBeacon with "ble_app_beacon" in SDK. As you know for estimating Distance, you should calibrate it. for calibration, place...
Hi,
I have IOS application which works fine with bluetooth different than NRF. I use direct connection by UUID in IOS app. When the application is in foreground everything...
Dear Sir,
I am new in nRF51 and used the ble_app_uart example in our application (nRF51), need power saving function but not necessary power off.
The sample code will...
Hi,
I am trying to implement timeslot API using s110 v8.0.0, SDK 8.0.0 on nRF51822-XXAA on a keil uVision 5 platform.
I have tried the following memory settings:
...
Hi
Regarding the NFC url example there is any way to change the URL dynamically. My idea is to, at a certain point, be able to modify the URL configured during the setup...
Hello,
I'm having an issue when trying to update the bootloader itself: NRF_UICR->NRFFW[1] returns 0xFFFFFFFF, which means I can't use the MBR command to swap bootloaders...
Our BLE product uses a meander PCB antenna similar to PCA10031. It works actually quite fine, but a question pops up when it comes to tuning.
Antenna matching design in...
I'm having some issues getting the auto ACK to work properly. I am only receiving auto ACK messages on the first 3 received packages, after which the receiver stops replying...
Hello i have a system that build in an ultrasonic sensor RedBearLab BLE Shield ( nrf8001 ) and arduino i want to get ultrasonic data via bluetooth and see it on nRFConnect...
Hi,
My host MCU controls nRF51 over SWD interface.
How can stop/halt nRF CPU? After initialization the SWD(init/read DB/AP AHB, etc.) I need to halt (stop nRF program...
Hi,
I would like to have one page of flash mapped manually to store information critical for the device. Let's assume I do not trust data preserving by DFU or there is...
I have some BLE traffic that I have sniffed and am displaying in Wireshark. Most of the opcodes (read/write request/response indications/notifications etc.) are parsed/displayed...