void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi
I am writing my own bonding manager.
In the S110 stack after Phase 3 of pairing the keys are exchanged which result in the EVT_AUTH_STATUS event which in turn contains...
when I add my own service and add characteristic, a odd phenomenon confuse me.
When I set cccd_md.write_perm:
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm);
...
after several attempts to debug and understand what goes in my handlers in the BLE callbacks, I thought to give a UART logger a try.
this is what I'm trying to use: OpenLog...
Hello,
I am looking for a not expensive way to program nRF51822 by frame of 10 modules. All the 10 modules would be connected to a PC using pogo pins, and I would use a...
I can get an information that bluetooth smart connects bluetooth smart ready.
But I can't get an information that bluetooth smart connect bluetooth smart ready.
So, Would...
I am using nrf51822 and i want to run my application using softdevice.
But I am not able to start my softdevice Please can anyone guide me how to start my softdevice.
I...
How to enable the notifications or indications? In APP? can I enable it in ble peripheral?
I meet a chip of "Quintic" can do this. When I connect it to MCP and I get this...
I made Pwm program with 3 channels without using softdevice and without using interrupts at that time it is working perfectly. But when i am trying to use softdevice with...
Sometimes I receive pipe error 0x92 when I try to send a message from nordic to Android. What could be the causes for a pipe error 0x92?
I saw this: "Pipe Error Event ...
Hi,
I purchased nRF24Lu+ modules on ebay. I am trying to talk to them over USB from a linux machine.
Nordic datasheet states:
VID = 0x1915 and
PID = 0x0101
When...
Am I right in thinking that these security parameters are contradictory in that for the peripheral (nRF51822) to provide MITM protection, there must be either IO capabilities...
I just received my nrf51822 and am using an-36 as a starting point to build my first "Hello World" application for BLE.
All I would like to test is to have the status of...
I am trying to only perform calculations for connected ble services.
I am implementing a state machine that monitors the ble evt.
I use this for example when to perform...
