Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
How do I reset nRF51822 to shut down the debug port?
I have a custom board with a built-in battery and strong power management.
If I power up the board without the debugger...
Hi All,
My goal is to advertise the generic packets untill a GPIO interrupt occurs. So in order to achieve low power consumption I have increased the time interval of those...
bootloader.rar (/attachment/d5fd4fbbc7d37433740f6c9468f3110b)
bootloader_dfu.rar
Hi,all.i want to set same macaddress with my app in bootloader,and advertise it in bootloader...
I have a pstorage Clear and Store that I use just before calling bootloader_app_start() in my DFU bootloader code. Everything was working great testing/compiling (GCC) under...
Hi,
we'd like to use nexus 7 II(android 5.1.1) to connect nrf51822, but cannot connect if nrf51822 uses whitelist.
step 1. we send advertising packets without using whitelist...
I'm trying to build our application using GNU Toolchain and currently facing compilation issue with __asm directive; the error thrown is:
../../NRF51_SDK_v6_1/nrf51822...
I usually see a system event "NRF_EVT_FLASH_OPERATION_ERROR" when updating my device firmware. SDK says that this event indicates that the ongoing flash operation has timed...
Hi, have anyone tested nrf51822 beacon smart kit on samsung tab 4? For some reasons it didn't detect the beacon. I have tested with company identifier of nordic, samsung and...
Since the IoT SDK is not support the IPSP Router role.
Is that mean the nRF51822 can't been used by other MCU which is running Contiki to become a Edge Router?
There are many links across the Internet to app note nAN-29 ( nRF51 Development with GCC and Eclipse ). In fact, I remember seeing a link to it on the Nordic website just...
Hi,
I am trying to test a UART bootloader with the hci_dfu_send_hex.py from SDK6.1.0
Unfortunately the script seems to crash, below is the output on the windows command...
Let's say I Have an nrf51822 on a small button cell battery having a sensor that is triggered on certain conditions.
What is the most efficient and power saving way to...
Hello. I'm using 24 MHz crystal to feed my MCU and not able to change it to 16 MHz to share with nrf24. Now I'm driving nrf24 XC1 with PWM signal 16 MHz and it works but not...
Hi,
We have NRF51822 chips programmed for specific application and it is working fine as BLE services etc.
In some scenarios, to debug we want to stream data from our...
device_manager_peripheral.c provided via Software Packs in Keil doesn't compile against S110 8.0.0 (or 8.1.0). Its version shows up as 1.1.1. Same thing happens with bsp.h...
