void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Is it possible to use the nrf51 dongle with raspberry pi b+ ? I'm prototyping a 6LoWPAN solution where the peripheral nodes are nrf51 devices. I'd prefer the central device...
Hi, I'm not used to the bsp.c so my question could be silly. I hope you could understand.
When I used SDK 6.1, the example about button_event_handler function had a parameter...
What is the best way to transfer an array of individual values using the BLE stack?
Is it by appending all the values into one blob and sticking it into a characteristic...
I'm using
HID keyboard example (SDK 7.2), Softdevice S110 7.1 , IAR for ARM 7.1, J-Link,
on my custom board (with NordicSemi nRF51822-QFAA MCU).
/***************...
I am designing a product with the nrf8002 chip and have a question on Power consumption. Lets say I leave all the default ratio's alone and use a CR1620 battery which has...
How can I read the Bluetooth clock (piconet) which is synchronized between the master/slaves in the piconet ? I need a constant (micro second accuracy) time from when I do...
Hello,
Is it possible to know the preamble , data format and the CRC calculation to interface a radio system ( GFSK Manchester) with NRF905 ?
Thank you
I'm wondering if the port and pin function can be used together to configure a set of pins.
For _port_dir_set, I assume it sets the whole port to the designated direction...
Hey i was using the code from developer.mbed.org/.../main.cpp
I am using this chip ( http://i.imgur.com/q8EM4uq.jpg ), it is nordic nRF51822 but i exactly do not know its...
I am using spi_master.c for spi communication with nRF51822EK.
And i had sent and recieved data packet successfully for 1st time with spi_master_send_recv(). When i sending...
Hi All,
I can compile and flash examples with my nrf51822 SDK on linux. I would like to use Code::Blocks as IDE.
Code::Blocks is transparent to run debugger. I try to...
I bought a blend micro to learn about arduino and BLE. I am a complete newbie in this field.
This is what I want to make happen,
I want to install my Blend Micro inside...
Hi All,
I am new in nrf51 development. I have a nRF51-DK kit. I would like to make development in Linux (Debian) only.
I found a lot of documents and I can compile examples...
My nRF Studio can not get nRF6130 board info,just show "Boards connected:".
But I can download fw to nRF51822 chip on the nRF6310 board.
The Application "ble_app_hrs" is...
What is the cleanest way to expose a dynamic (non-fixed amount of entries) through BLE?
One way I thought of is to create a service for a single table entry and go through...
