I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hi,
Now, I'm doing a project. A device node sends picture data and the other one receives these data. Then the receiver shows the picture on the SSD1306 display.
At receiver...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Hello, I am working with the nrf52832 and was trying to understand the steps for configuring the Bluetooth stack. Does anyone know what role the APP_BLE_CONN_CFG_TAG plays...
Problem
We have manufactured a custom board using the nRF9151 and we ran into some manufacturing QA/QC issues. The reserved pins of the SiP are very close to ground pads...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hi all,
I'm looking into speeding up my workflow using remote development containers on ARM servers, but it seems some tools are missing, nrfutil the first, to run a fully...
Is it possible to see LOG_INF() or LOG_ERR() messages from custom board software when the custom board is connected to a nRF52840DK through connector P20? The custom board...
I have an application that I want to build and run on 5 or 6 target devices including a nRF52840DK, nRF52840 Dongle, and custom boards. There are areas of the code that only...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
