Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi all,
I could not find similar questions raised on the forum and I hope someone can help me.
I have an application to connect to a mqtt server, developped on the latest...
Using NCS 3.0.2 I have multiple build variants of my project, based on the same custom PCB but with different parts fitted, and different functionality. So I have create different...
Hi all
I’m having a horrible time trying to get an nRF7002EB Wi-Fi coprocessor working with a nRF52840 via QSPI interface in nRF Connect SDK 3.0.2 (Zephyr 4.0.99). I'm using...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello,
I'm working with Distance Measurement (nrf_dm) using the NORAB126 module on nRF Connect SDK v2.9.0 and nRF Connect SDK v3.0.1.
I'm facing an issue where, occasionally...
Hi,
I’m trying to use the SoftDevice Controller in peripheral-only mode on the nRF54L15 (using NCS 3.0.1), but I can’t get it to build with `CONFIG_BT_LL_SOFTDEVICE_PERIPHERAL...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
hi support team,
i have one problem for 54l15+7002 in ncs2.9.0
I am afraid that I need your help.
I was porting MQTT demo and PERIPHERAL_UART demo together and want...
Hello, Nordic Team! I am encountering a such problem when using the NRF54L15 on NCS3.0.2 to develop a Matter product. I am trying to use the
SubscribeAttribute
method...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
Hello Nordic Team,
For my application, I am using two nRF54L15 chips with one configured as a master and the other a slave. For the remainder of this post, I will be discussing...
Hi,
Background:
We're developing wireless application with the NRF5340-NRF7002 chipset, similar to what's on the 7002DK board.
We'd like to put the system to lowest...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hi
I have a PDM microphone which is connected to the nrf5340. I am currently buidling it with the audio_dk device tree and have modified the UART pins. There are no other...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
