Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
based on SDK v2.9.0
1 Central, 4 Peripherals, Repeat the following:
Power off 3 Peripherals, wait a while, power on 3 Peripherals.
The following error usually occurs...
Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
After connecting to an nRF9160 using SEGGER tools (J-Link RTT Viewer v7.62b), excess power consumption is observed until the device is reset (via `nrfjprog -r`)
First the...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hello Nordic Team,
For my application, I am using two nRF54L15 chips with one configured as a master and the other a slave. For the remainder of this post, I will be discussing...
Hi, having some issues with the matter door lock sample for the nRF54L15DK on NCS 3.0.2. I'm getting strange failures on boot when running the default matter door lock sample...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
I used two development boards with 52840, Two development boards are running 'first' and 'second' in the '\examples\802_15_4\wireless_uart\secure', respectively.
Additionally...
Hello,
I'm working with Distance Measurement (nrf_dm) using the NORAB126 module on nRF Connect SDK v2.9.0 and nRF Connect SDK v3.0.1.
I'm facing an issue where, occasionally...
Hi,
We're currently evaluating the cellular capabilities of the nRF91 modem using the nRF9151 DK. We've encountered issues with roaming: when the devkit is taken to another...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
