I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Hi everybody! I am here again bothering you with probably silly questions. I have, on my smart beacon kit, an application that uses an ADC and then sends the converted value;...
`Hi Guys,
My project requirement is that first time i have to bond and connect my nRF8001 BLE with peer device, once connected i have to find peer device address, after finding...
Hi everyone,
I was not able to find a full example in the SDK or online on initializing ANT to work with burst mode. Also, I was wondering if it's possible to setup ANT...
Hello,
I have a design where nrf51422 works as companion chip together with an other uC as main controller (STM32F4).
I need to reset the NRF from the main controller...
Hi,
For our new product we are using nRF52832 chip for BLE and NFC. We have a query regarding the NFC section which is listed below-
Please refer the recommended EMC filter...
I have captured the ble packet showing as the screenshot by using the ble sniffer(win7 ) and wireshark.
But I did not understand the meaning of delta time (such as end to...
Hello!
I would like to whitelist a peripheral when -60 dBm RSSI is achieved (this means that central will bond to peripheral by proximity) but later data exchange must...
Hi all, i have an application with a smart beacon kit; i won't resume the whole project because it's long and boring, i will just say that i have a service that every 100...
Hi,
I'm using the S110 v8.0 on a nrf51422 together with our own scheduler with a few lines left from SDK v8.1.
I'm sending out advertising containing some extra data and...
Dear
As far as I know, the nRF51822 has the Pin Crossbar feature that weu can chose and connect
any GPIO pins as second UART.
I need to talk to two UART peripherals...
Hello Everyone,
I have created an schematic for m custom prototype using NRF51BLE with Sigfox Radio chip whenever i press the button on the NRF51i has to send message to...
Hello,
is there a trick, how the Radio peripherals device address match feature could be used to implement those advertising filter policies that filters based on the PDU...
I want to program the ARM MCU in the nRF51822 Development Kit for my own purposes and then send the processed data using the BLE module in the kit to another nRF51822 Development...
I have been using this mode to init the app_uart_fifo code on SDK8 for a while now and when moving over to the SDK11 code I was in the app_uart_fifo.c code and it's radically...
Has anyone taken the Nordic LE Secure ECDH key exchange and encryption code though FIPS 140-2 certification and what level was attained? I was tasked with getting to level...
