Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
During my development with ANT protocol, I found that if you have a bunch of units all have one master channel. Channels will actually bump into other channels easily and...
Hi,
I'm trying to get the SPI Slave example working on my nRF51822 PCA100001 development kit.
SPI1_TWI1_IRQHandler never gets called even though the ACQUIRED and...
Looking into the schematics, I could not find any uart or spi signals on the connectors. I am good in soldering, but I would not dare connecting wires to the nrf51422... ...
Hallo everyone!
I need very low consumption when BLE working. according to S110 SDS, BLE power profile section, when BLE in idle-connect, there is Ion+Irtc+Ix32k, same...
Use the spi_master_example_with_spi_slave in SDK6 to evaluate the SPI master module but fail.
No matter use the default pin assignment or re-assign, it does not give out...
I can't find in the documentation for the IoT the usual section about requirements for the start of user code, the start of user RAM, the max stack used and whether any heap...
I would like to be able to generate DTMF tones using PWM. I am very familiar with the process, having written code to do this several times on other devices. The DTMF will...
Is it possible to use the nrf51 dongle with raspberry pi b+ ? I'm prototyping a 6LoWPAN solution where the peripheral nodes are nrf51 devices. I'd prefer the central device...
Hi, I'm not used to the bsp.c so my question could be silly. I hope you could understand.
When I used SDK 6.1, the example about button_event_handler function had a parameter...
What is the best way to transfer an array of individual values using the BLE stack?
Is it by appending all the values into one blob and sticking it into a characteristic...
I'm using
HID keyboard example (SDK 7.2), Softdevice S110 7.1 , IAR for ARM 7.1, J-Link,
on my custom board (with NordicSemi nRF51822-QFAA MCU).
/***************...
I am designing a product with the nrf8002 chip and have a question on Power consumption. Lets say I leave all the default ratio's alone and use a CR1620 battery which has...
How can I read the Bluetooth clock (piconet) which is synchronized between the master/slaves in the piconet ? I need a constant (micro second accuracy) time from when I do...
Hello,
Is it possible to know the preamble , data format and the CRC calculation to interface a radio system ( GFSK Manchester) with NRF905 ?
Thank you
