Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Exactly what baluns are known to work with the nRF51822. I believe there is the STMicro balun and am uncertain about the status of the Johansen balun. Is there a list of preferred...
Hi,
We are using nRF51422 in our project and we observe a strange thing, that even there is no external pull up resistors, the I2C communication using the built-in TWI...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Hi,
I am trying to create a star network with 12-16 slaves and one master.
The master would be a nrf51822 and the slaves nRF8001/2.
The slaves would not transmit...
Hi,
I'm using the UART_OVER_BTLE base example and I'm investigating what needs to be done to enable security.
Using the Following security configuration the device stops...
Can you tell me which antennaes i can connect with nRF 8001 to make it discoverable and transfer data. And i think pi network is solved depending on the antennae only. Can...
Hi,
Is it possible to extend the RAM memory by using internal flash memory?
Actually i need to collect 4KB of data from accelerometer and flash it to the EEPROM when there...
I'm working on a device which may spend months, or even years as deep as 1000 ft underwater...a harsh environment. Accordingly, the PCB will be completely encased in plastic...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
The 10000 dongle does get detected in nrfgo Studio but the 10001 board does not. There are no USB devices with exclamation marks or otherwise undetected when the 10001 is...
Hey folks,
I am currently trying to expose a local name for my nrf51822 chip but whenever i change it from NO_NAME to any of the other options and run the program it doesn...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hi,
I need the 16 bit timer1 to have high priority, how do i set this to a high priority? And what priority does it have in my case when i use:
NVIC_EnableIRQ(TIMER1_IRQn...
Hello
I have a nRF51822-EK evaluation kit, I have succesffuly installed the nRFgo studio and Seggger software so that I can detect the dongle and it shows up on device...
