Hello, I'm working on my Senior project for school and it involves me creating a PCB that will be utilizing the NPM1300_QEAA. Is there a footprint model for it in Altium,...
Hi,
Now, I'm doing a project. A device node sends picture data and the other one receives these data. Then the receiver shows the picture on the SSD1306 display.
At receiver...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Hi,
I am attempting to run the examples of BLE HRS C and BLE HRS Peripherals from the SDK. Getting to the connected state works (discovery and notifications as well) just...
I noticed that the ram setting in this example is from 0x20003440, this means only less than 1KB is for application. But the example in sdk 12.1 the ram is from 20002078....
We want to use IoT SDK where two or more nRF52 chips would talk to each other via 6lowpan, in that case is the ble enabled router necessary for such communication?
I have an nrf51822AC chip connected to another ARM based processor which provides a CAN interface. The two are connected via the UART and we are using the ble_connectivity...
Hi, in the current project I'm working on, I need to develop an Eddystone beacon with UID and TLM frames configured by default. Based on the experimental_eddystone example...
Hi, Nordic
I need write some information to flash, then power off and power on, nRF52 still can read previous information. But now, nRF52 can not read, maybe ESB is still...
Hi,
I'm having issues with my MPU6050 sensor. I'm trying to get yaw, pitch and roll raw sensor values from MPU6050 sensor using DMP on MBED platform but without success...
I have just read nRF52840 Engineering A Errata v1.0, it looks like nRF52840 is like swiss cheese.
When can we expect some solid version of nRF52840 chip on the market?
Hi DevZone
Does the SWF switch at the PCA10040 automatically switch to the antenna I have put on my connection probe? ( www.digikey.com/.../1775923)
Thanks in advance...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Sir,
I am working in nRF52832 board with pca10036. I want to know whether the board supports a loopback control in SPI mode. I need to try for transmitting and receiving...
Hello,
I'm trying to use NFC module on nrf52382 chip (DK PCA10040) and prepared firmware "nfc_text_record_pca10040" from examples of SDK v13. After flashing the Mifare ultralight...
Hi,
In the nrf52.h, SPIM_RXD_Type is defined as below.
typedef struct {
__IO uint32_t PTR;/*!< Data pointer */
__IO uint32_t MAXCNT;/*!< Maximum number of bytes...
