Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I'd like to retain a few bytes after a restart from system_off. I know the GPIO state is retained, are there any other registers other than that? It looks like RTC1->CC[0...
I've been struggling for some time to get L2CAP transfer between an NRF51822 and a Linux machine using bluez.
I've successfully created a connection between the central...
Hi,
I want to understand ANT and want to begin development with ANT once I figured out how it works. After reading posts on this forum I found out that not all Softdevice...
Is there an example for using a 10 pin 2 digit 7 segment display similar the picture below?
It is common anode and actually has 10 pins (pin 2 is the DP or decimal point...
Hi,
I was wondering about that I did not found any information about dedicated pin usage.
I am using I2C/SPI and UART and did I understand it correctly that i can use...
My application has two firmwares with different offset addresses. One firmware sitting at 0x16000 and second one is at 0x25000. I want jump to the second application from...
I have an issue where after transmitting a radio package, is setting up the radio as receiver, get indication for reception (have indications for ADRESS and PAYLOAD events...
I programmed my beacons with ble_app_beacon (nordic firmware). android can locate my beacons without any problems.
I installed nrf connect app, it can find them too.
but...
Hello,
I'm using BLE, RTC and app_timer to blink a led.
I blink the led 10 times when I receive an order from BT (by means of NUS), and then by means of RTC.
uint32_t...
Hi. I'm very new to this so I hope you'll forgive me for my basic questions!
I would like to take data from multiple ANT fitness devices and send it to an iPhone application...
Hi,
I'm designing a 2 layer flex PCB with the nRF51822-CFAC WLCSP package and recommended ST BAL-NRF02D3 balun and i have chosen mono-pole antenna is a good choice,because...
I Programmed my beacon devices with this firmware:
ble_app_beacon.zip
the only app that can find my beacon on ios is nrf connect. in this firmware the uuid is this:
...
I am trying to change the app beacon example so that i can adapt the beacons value each time it advertises.
I am a bit confused as there is no callback function called...
