Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello! I need to perform some radio tests on a board that contains an nRF52 SoC. The nRF5 SDK provides two ways of performing such tests, either using DTM, as specified by...
Hello,
I am using pca10028 dk. I want to know how can I change the transmitting power of ble?
My application needs that user should be able to change the transmitting power...
Hello guys!
I got a board of nRF52 with a Jlink debugger on it through a serial port and I program it with nrf-connect-mesh-official-serial-gateway-fw.hex.
However, when...
I am programming a Ble Nano device using Nordic SDK. So far I have been using examples from the ble_peripheral and ble_central directories. Now I want to run an example that...
Hi,
I used the nrf51822 as the spi master,it could send out the data, but it didn't receive the slave data.Did I miss somthing?
static volatile bool m_transfer_completed...
I'm working the the NRf52 dev board and SDK12.2. I was able to successfully load the standard DFU example and then use the NRF Toolbox on an android to load the example HR...
Hi.
I'm getting an nRF Dongle (PCA10031) set up on a Windows machine to be the BLE central that we'll use for our production line testing. To that end, I've built the pc...
The pc-ble-driver project uses CMake to generate Solution and Project files for the Windows build of the project. CMake uses absolute paths in these generated files. I can...
Working with nRF52832 and SD132-v2.0.1
Using Timer 1 at 1MHz (pre-scale 4) and 32bit bitmode CC to trigger events at a pretty wide range (from us to minutes).
I'm getting...
I am calling certain services and I can see this output on my UART listener:
0.000013 : UART Start!
0.385355 : BLE Stack Initialized
0.385581 : Peer Manager Initialized...
What would be the best value for UART buffer?
When I put it as 512 it gets crashes, below you can see the putty output
0.000013 : UART Start!
0.415937 : Handle list for...
I want to use app sched feature, so as example does, I call:
static void scheduler_init(void)
{
APP_SCHED_INIT(SCHED_MAX_EVENT_DATA_SIZE, SCHED_QUEUE_SIZE);
}
since...
Hi Team,
I need to make an application that we receive a data from a chip through UART and need to send the data to Console through another UART. Is it possible to make...
Hello,
My setup:
PCA10040 DK,
12.2 SDK
I copied the "BLE_APP_UART" example into my project folder and want to "upgrade" it with the TWI.
So I copied parts of the "twi_scanner...
