Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I am using an RTC for other purposes that exposes a buffered 32kHz clock. I am considering using the buffered (rail-to-rail) for also the LF timebase of the nRF51. The drive...
I've just discovered that the Jlink LITE programmer can not program my custom PCB because it runs at 2.7V.
Does the nRF51-DK board support programming an external target...
Hi....
We are working on PCA10028 DK with S130 softdevice version 0.9.0 alpha. Could you tell me about the release of stable SD S130. Hope it will be soon.
Hey,
Is it possible to use the NRF51822 for connectivity together with Arduino, and if so are there any easy instructions as to how to do so? I am looking something on...
Hello I was wondering if I can use both the proprietary protocol 2.4 Ghz ( I understood the one to use for the new projects is Gazell ) and the Blueotooth smart on the nRF51422...
Recently,I met a problem when I used Gazell mode. Before, i used the GPIOTE to collection PPM receiver 's length of time, when I also use the gpiote and wireless data transmitting...
Hello , i have been following the ANCS tutorial and have managed to pair it with my iOS device. I am using the Nrf8001 with an arduino. I have read up many articles about...
I have seen several good questions and answers on this forum regarding the use of a PA for extending range of the nRF51422/nRF51822 devices. I have a battery-powered application...
Hello everybody,
We are using a nRF51288 with an external DCDC converter. VDD and AVDD is bridged, DCC is not connected.
The software is working in Peripheral mode, S110...
hello,
I recently purchased a NRF51 dongle and NRF51 DK. I was working with older version of NRF51 development kit. I did n't get any information in the user guide provided...
Hello,
when using the S130 with multiple connections and sporadic advertisement and scan procedures, I get a connection timeout after a few minutes, now I must know, how...
Hi,
Im using an app_timer in my application to create a timeout for UART read (im not using SoftDevice).
On my board I have USB and battery power, so at the moment when...
After switching to 51822 in example project nRF_Examples\7.0.1\dfu\bootloader\
I have next output:
compiling pstorage.c... compiling bootloader.c... compiling bootloader_settings_arm...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
