I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have NRF 51 DK.
I adjusted the toolchain path to arm-gcc 4.9 2015q1. This version works fine for the NRF 51 SDK.
I get this error:
lto1.exe: fatal error: bytecode...
I'm seeing the resetreas show the CPU lock-up detected after I reboot. This error is occurring while using the ADC. What type of fault condition can cause a CPU lock-up detection...
Hey everyone,
I'm developing an application using the IoT SDK . The first part of the application consisted of a normal BLE peripheral to interact with an android app....
app_timer.h contains a useful macro for getting from milliseconds to a number of timer ticks, given a prescaler value with which the timer was started:
#define APP_TIMER_TICKS...
Hello,
May i know what will happen if we happen to assign the same pipe address for let's say pipe 1 and pipe 2?
Can we still receive data and be informed of the pipe...
Hi,
My goal is to send temperature values on the advertising so, I'm trying to get work this example, but i have an error about this lines of the code on keil:
advdata...
Hello, how can i modify the hrs_s_evt_handler() to initiate bonding only if it my configured belt address?
My Solution:
static void hrs_c_evt_handler(ble_hrs_c_t * p_hrs_c...
Hello, All.
I want to know AppID in iPhone's App using ANCS.
(for example, Facebook App's AppID is "com.facebook.Facebook",
Facetime's AppID is "com.apple.facetime")...
Hi Nordics!
I want to add custom service into ANCS example for android.
But I cannot understand how to add custom service stably.
First, I just added my custom service...
I have compiled the nRF51-ble-bcast-mesh 's examples: "LED_mesh_SDK7" and "BLE_Gateway_SDK7" on Keil uVision v5.14.0.0. But, I am facing problems flashing them on to my nRF51422...
I have a problem that I can't figure out. I have a custom board with an nRF51822 QFAB. The board will run a test application that uses nrf_delay_ms() to toggle an output pin...
Hi!
I have reviewed the NRF518 reference design, i.e., case "PCB layout recommendations for the NRF51822 WLCSP62 package" and the layout pdf files provided therein:
...
Hi
I have read various things about this so I would like to confirm
What is the best way to set the bluetooth address of my device ? Is it built in by nordic ?
Or is it...
Hi,
I am able to change the MAC address of the beacon using the call sd_ble_gap_address_set(BLE_GAP_ADDR_CYCLE_MODE_NONE, &gap_addr), where gap_addr is of type BLE_GAP_ADDR_TYPE_RANDOM_STATIC...
