I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Dear Nordic
Does Nordic have a passive writable chip available (with compat antenae) that can be activated by mobile device bluetooth scanning event. The mobile device...
Hello
I am trying to run the dual mode BLE/Gazell application example ble_app_gzll. I adapted it slightly such that the stacks are switched automatically in main() as follows...
Hello
I'm using nrf51822 EK board. This is my first time to develop application in ARM system.
I want to develop a ble application.
This application can be shut down (system...
I've got my custom PCB design assembled. Attached segger jlink, but it detects only 0.1 V, although Vdd is 3V.
How is the power measured?
What should I read on SWDIO...
Dear
Is there a possibility within Nordic SoC to make a passive RFID Tag which will connect to SmartPhone via Bluetooth?
Just like µBlue Series, but smaller and using...
I found the "S110_SoftDevice_Specification_v1.2.pdf" but not the "S110 softdevice release notes" mentioned in a previous question about DCDC usage. Where is that doc?
What...
I have been developing on a nrF51422 QFAAC0 chipset. That chipset required SDK 4.4 for soft device capability.
I requested the latest silicon (so I could develop against...
Hello,
I would like to build a tool in Python that allows sniffing/interaction with BLE traffic between nRFgo modules (nRF51822) and a Mac via the master emulator. I am...
I have bought the Bluetooth low energy evaluation kit nRF51822. It can be paired with a Nexus and a Sony Xperia without problems, but it does not appear at all on Samsung...
L.S.
Today I decided to have a look at SDK5.1.0 for nRF51822 which supports the S120.
It is deliverd as an msi file with (as far as I have noticed) no support for specifying...
Is there anything preventing anyone from uploading the tinyest image that simply dumps the entire ROM content on the UART?
This would sort of circumvent the HW locking...
Hello,
I use nRF51822 for my project and I would like to purchase some BLE packet sniffer. Does anyone recommend any sniffer? My purpose for that is debugging and check transaction...
On PCB layouts I often see that the HF xtal is oriented at 45 degrees relative to the orientation of the 51x chip (that is to say the edges of the the xtal and 51x chips are...
Hello Nordic expert,
Regarding the antenna load impedance, I can find the data in nRF24L01+ datasheet and it is 15ohm +j88ohm.
But I can not find the antenna load impedance...
hi,
now ,i have save the power,so need to close the spi interface at some time.
but when i call follow function (hal_spi_disable).
it see not close the spi interface, ...
