Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I know that Vdd on nRF24L01 module should be on 3.3V power and probably will be burned if get 5V power.... If in any case that happen at some point of experimentation...
Hello!
The company for which I work is migrating from NRF24 to NRF51.
Our protocol relies on ESB and uses payloads of 32 bytes and payloads in ack (also 32 bytes).
...
Hi,
after receiving button event application crashes. I get NRF_ERROR_NOT_FOUND from app_sched_event_get and device stop responding.
What can be the reason?
Thanks...
Hi,
recently I purchased the nRF51822 Beacon Kit. I downloaded the hw files and unfortunately realized that they are altium designer files.
As I'm using Eagle I would like...
Dear All,
I've recently had a problem with interaction with samsung phones (S3, S4, note 2 on 4.3+) using 51822. The connection interval that I have is around 48ms with...
**nRF8001 + STM32 microprocessor + ble_HID_keyboard_template (from Arduino)**
I am now trying to port the ble_HID_keyboard_template from the Arduino:
After the reset...
Hello support team
Have you tested the nRFgo 1.15 x64?
usually x64 installs in Program Files this installs in Program Files (x86) any reason why?
I had to recover my PCA10001...
is there any complete altium designer file including schematic and pcb file for nrf51822 ?? there is only layout file in the website...... if you have it please email the...
Hi
I just updated our project to files from new SDK release 6.1. The normal application is working properly with the new SDK, but i got in trouble with the bootloader parts...
Hi all
I would like to use the s110 softdevice V7 with the nRF51422 which I know is possible. However, I would like to start the work with an example project, but I can...
I want to make a indoor positioning system using bluetooth 4.0. so for this HOST should recieve the RSSI from the devices it is connected to(from RSSI to distance conversion...
Hello,
I am working with the nRF8001 device:
When I try to configure the device as a service data broadcaster and go to the nRF8001 Setup -> Generate Source Files (in...
For improving my data trouchput (both directions, using »Write without response« and »Notification« like e.g. nRF Uart Example do9, I'd performed some tests regarding the...
